Скачал, распаковал на винт, сделал загрузочную флешку, загрузился, стал ставить, на середине установки писать на винт суся отказался. Пошёл другим путём: поставил по сети. SLED встаёт всегда SLES иногда "спотыкается" на том же нежелании писать на винт. При этом возникает irq 169, на котором и висит контроллер...
После установки SLED постоянно зависает: 10 минут, 20, пол часа... Всё равно встаёт намертво с горящей лампочкой чтения винта.
Вопрос, что это может быть? Куда копать? На текущий момент пробовал загружаться в failsafe режиме, но всё равно система подвисает.
конфигурация системы:
mb: ASUS P4P800-VM, биос перепрошил на 1018 версию чтоли.
3 винта: 1xIDE, 2xSATA + CD-ROM на IDE.
1256мб оперативки.
Гружусь с флешки на 4ГБ (далее она там "видна")
Пробовал играться настройками биоса, чтот не помогает.
далее /var/log/boot.msg
[more=boot.msg]
[no]
Inspecting /boot/System.map-2.6.16.46-0.12-smp
Loaded 22646 symbols from /boot/System.map-2.6.16.46-0.12-smp.
Symbols match kernel version 2.6.16.
No module symbols loaded - kernel modules not enabled.
klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.16.46-0.12-smp (geeko@buildhost) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) #1 SMP Thu May 17 14:00:09 UTC 2007
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000004ff30000 (usable)
<4> BIOS-e820: 000000004ff30000 - 000000004ff40000 (ACPI data)
<4> BIOS-e820: 000000004ff40000 - 000000004fff0000 (ACPI NVS)
<4> BIOS-e820: 000000004fff0000 - 0000000050000000 (reserved)
<4> BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
<5>383MB HIGHMEM available.
<5>895MB LOWMEM available.
<6>found SMP MP-table at 000ff780
<7>On node 0 totalpages: 327472
<7> DMA zone: 4096 pages, LIFO batch:0
<7> DMA32 zone: 0 pages, LIFO batch:0
<7> Normal zone: 225279 pages, LIFO batch:31
<7> HighMem zone: 98097 pages, LIFO batch:31
<6>DMI 2.3 present.
<3>Unknown genapic `apic=verbose' specified.
<6>Using APIC driver default
<7>ACPI: RSDP (v002 ACPIAM ) @ 0x000fad50
<7>ACPI: XSDT (v001 A M I OEMXSDT 0x09000505 MSFT 0x00000097) @ 0x4ff30100
<7>ACPI: FADT (v003 A M I OEMFACP 0x09000505 MSFT 0x00000097) @ 0x4ff30290
<7>ACPI: MADT (v001 A M I OEMAPIC 0x09000505 MSFT 0x00000097) @ 0x4ff30390
<7>ACPI: OEMB (v001 A M I OEMBIOS 0x09000505 MSFT 0x00000097) @ 0x4ff40040
<7>ACPI: DSDT (v001 PPVM1 PPVM1911 0x00000911 INTL 0x02002026) @ 0x00000000
<6>ACPI: PM-Timer IO Port: 0x808
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>Processor #0 15:2 APIC version 20
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
<4>Processor #1 15:2 APIC version 20
<6>Overriding APIC driver with bigsmp
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
<7>ACPI: IRQ0 used by override.
<7>ACPI: IRQ2 used by override.
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode: Physflat. Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 60000000 (gap: 50000000:afb80000)
<4>Built 1 zonelists
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 apic=verbose irqpoll apm=debug dmi=debug resume=/dev/sda1 splash=silent showopts
<4>Misrouted IRQ fixup and polling support enabled
<4>This may significantly impact system performance
<6>bootsplash: silent mode.
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 65536 bytes)
<4>Detected 2394.330 MHz processor.
<6>Using tsc for high-res timesource
<4>Console: colour VGA+ 80x25
<4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 1290980k/1309888k available (1643k kernel code, 17536k reserved, 747k data, 196k init, 392388k highmem)
<4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>Calibrating delay using timer specific routine.. 4817.86 BogoMIPS (lpj=9635731)
<6>Security Framework v1.0.0 initialized
<4>Mount-cache hash table entries: 512
<7>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<7>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<7>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<6>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
<6>CPU0: Thermal monitoring enabled
<6>Checking 'hlt' instruction... OK.
<6>checking if image is initramfs... it is
<6>Freeing initrd memory: 2405k freed
<4> not found!
<4>CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
<4>enabled ExtINT on CPU#0
<4>Leaving ESR disabled.
<6>Enabling SMP...
<4>Booting processor 1/1 eip 3000
<6>Initializing CPU#1
<4>masked ExtINT on CPU#1
<4>Leaving ESR disabled.
<4>Calibrating delay using timer specific routine.. 4788.38 BogoMIPS (lpj=9576768)
<7>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<7>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<7>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#1.
<6>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
<6>CPU1: Thermal monitoring enabled
<4>CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
<6>Total of 2 processors activated (9606.24 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
<6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 12353.2767 MHz.
<4>..... host bus clock speed is 1029.1896 MHz.
<6>checking TSC synchronization across 2 CPUs: passed.
<6>Enabling SMP...
<6>Brought up 2 CPUs
<4>migration_cost=74
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
<6>PCI: Using configuration type 1
<6>ACPI: Subsystem revision 20060127
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>PCI: Probing PCI hardware (bus 00)
<4>PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
<4>PCI quirk: region 0480-04bf claimed by ICH4 GPIO
<7>Boot video device is 0000:01:00.0
<4>PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
<6>PCI: Transparent bridge - 0000:00:1e.0
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 *14 15)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>pnp: PnP ACPI: found 14 devices
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<7>number of MP IRQ sources: 15.
<7>number of IO-APIC #2 registers: 24.
<6>testing the IO APIC.......................
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>....... : physical APIC id: 02
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 000 00 1 0 0 0 0 0 0 39
<7> 02 000 00 0 0 0 0 0 0 0 31
<7> 03 000 00 1 0 0 0 0 0 0 41
<7> 04 000 00 1 0 0 0 0 0 0 49
<7> 05 001 01 0 0 0 0 0 0 0 51
<7> 06 000 00 1 0 0 0 0 0 0 59
<7> 07 001 01 0 0 0 0 0 0 0 61
<7> 08 000 00 1 0 0 0 0 0 0 69
<7> 09 001 01 0 1 0 0 0 0 0 71
<7> 0a 000 00 0 0 0 0 0 0 0 79
<7> 0b 001 01 0 0 0 0 0 0 0 81
<7> 0c 000 00 0 0 0 0 0 0 0 89
<7> 0d 000 00 1 0 0 0 0 0 0 91
<7> 0e 000 00 0 0 0 0 0 0 0 99
<7> 0f 001 01 0 0 0 0 0 0 0 A1
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<6>Using vector-based indexing
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<6>.................................... done.
<4>Setting up standard PCI resources
<6>pnp: 00:09: ioport range 0x680-0x6ff has been reserved
<6>pnp: 00:09: ioport range 0x290-0x297 has been reserved
<6>pnp: 00:0b: ioport range 0x3f6-0x3f6 has been reserved
<6>PCI: Bridge: 0000:00:01.0
<6> IO window: disabled.
<6> MEM window: fc900000-fe9fffff
<6> PREFETCH window: d7f00000-f7efffff
<6>PCI: Bridge: 0000:00:1e.0
<6> IO window: d000-dfff
<6> MEM window: fea00000-feafffff
<6> PREFETCH window: disabled.
<7>PCI: Setting latency timer of device 0000:00:1e.0 to 64
<6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
<6>apm: entry f000:ef50 cseg16 f000 dseg 40 cseg len ffff, dseg len 100 cseg16 len 0
<5>apm: disabled - APM is not SMP safe.
<6>audit: initializing netlink socket (disabled)
<5>audit(1203356367.768:1): initialized
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Initializing Cryptographic API
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Real Time Clock Driver v1.12ac
<6>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
<4>PNP: PS/2 controller doesn't have AUX irq; using default 12
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
<6>00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>mice: PS/2 mouse device common for all mice
<6>input: AT Translated Set 2 keyboard as /class/input/input0
<6>input: PC Speaker as /class/input/input1
<6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: bitmap version 4.39
<6>NET: Registered protocol family 2
<4>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<4>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<4>ACPI wakeup devices:
<4>P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K ILAN
<6>ACPI: (supports S0 S1 S3 S4 S5)
<6>Freeing unused kernel memory: 196k freed
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<5>SCSI subsystem initialized
<6>ICH5: IDE controller at PCI slot 0000:00:1f.1
<4>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
<6>ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
<6>ICH5: chipset revision 2
<6>ICH5: 100% native mode on irq 169
<6> ide0: BM-DMA at 0xef90-0xef97, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0xef98-0xef9f, BIOS settings: hdc:pio, hdd:DMA
<7>Probing IDE interface ide0...
<4>hda: QUANTUM FIREBALLP AS20.5, ATA DISK drive
<4>ide0 at 0xefe0-0xefe7,0xefae on irq 169
<6>hda: max request size: 128KiB
<6>hda: 40132503 sectors (20547 MB) w/1902KiB Cache, CHS=39813/16/63, UDMA(100)
<6>hda: cache flushes not supported
<6> hda: hda1
<7>Probing IDE interface ide1...
<4>hdd: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive
<4>ide1 at 0xefa0-0xefa7,0xefaa on irq 169
<7>libata version 2.00 loaded.
<7>ata_piix 0000:00:1f.2: version 2.00ac7
<6>ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
<6>ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>ata1: SATA max UDMA/133 cmd 0xEF88 ctl 0xEF86 bmdma 0xEE60 irq 169
<6>ata2: SATA max UDMA/133 cmd 0xEF68 ctl 0xEF82 bmdma 0xEE68 irq 169
<6>scsi0 : ata_piix
<6>ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
<6>ata1.00: ata1: dev 0 multi count 16
<6>ata1.00: configured for UDMA/133
<6>scsi1 : ata_piix
<6>ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
<6>ata2.00: ata2: dev 0 multi count 16
<6>ata2.00: configured for UDMA/133
<5> Vendor: ATA Model: ST3320620AS Rev: 3.AA
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<6> sda: sda1 sda2 sda3
<5>sd 0:0:0:0: Attached scsi disk sda
<5> Vendor: ATA Model: ST3320620AS Rev: 3.AA
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
<5>sdb: Write Protect is off
<7>sdb: Mode Sense: 00 3a 00 00
<5>SCSI device sdb: drive cache: write back
<5>SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
<5>sdb: Write Protect is off
<7>sdb: Mode Sense: 00 3a 00 00
<5>SCSI device sdb: drive cache: write back
<6> sdb: sdb1
<5>sd 1:0:0:0: Attached scsi disk sdb
<6>BIOS EDD facility v0.16 2004-Jun-25, 4 devices found
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>sd 1:0:0:0: Attached scsi generic sg1 type 0
<4>Attempting manual resume
<5>ReiserFS: sda2: found reiserfs format "3.6" with standard journal
<5>ReiserFS: sda2: using ordered data mode
<4>reiserfs: using flush barriers
<5>ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
<5>ReiserFS: sda2: checking transaction log (sda2)
<5>ReiserFS: sda2: Using r5 hash to sort names
<6>Adding 2104472k swap on /dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part1. Priority:-1 extents:1 across:2104472k
<6>hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
<6>Uniform CD-ROM driver Revision: 3.20
<6>e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
<6>e100: Copyright(c) 1999-2005 Intel Corporation
<6>ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 177
<6>e100: eth0: e100_probe: addr 0xfeaff000, irq 177, MAC addr 00:0C:6E:78:00:EE
<6>ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 185
<7>PCI: Setting latency timer of device 0000:00:1f.5 to 64
<6>usbcore: registered new driver usbfs
<6>usbcore: registered new driver hub
<6>USB Universal Host Controller Interface driver v2.3
<3>hw_random: RNG not detected
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
<6>Linux agpgart interface v0.101 (c) Dave Jones
<6>intel8x0_measure_ac97_clock: measured 70529 usecs
<6>intel8x0: clocking to 48000
<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>uhci_hcd 0000:00:1d.0: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
<6>uhci_hcd 0000:00:1d.0: irq 193, io base 0x0000eec0
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb1: SerialNumber: 0000:00:1d.0
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
<7>PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
<6>uhci_hcd 0000:00:1d.1: irq 201, io base 0x0000ef00
<6>usb usb2: new device found, idVendor=0000, idProduct=0000
<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: UHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb2: SerialNumber: 0000:00:1d.1
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
<7>PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000ef20
<6>usb usb3: new device found, idVendor=0000, idProduct=0000
<6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:1d.2
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 193
<7>PCI: Setting latency timer of device 0000:00:1d.3 to 64
<6>uhci_hcd 0000:00:1d.3: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:1d.3: irq 193, io base 0x0000ef40
<6>usb usb4: new device found, idVendor=0000, idProduct=0000
<6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:1d.3
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>usb 1-1: new full speed USB device using uhci_hcd and address 2
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209
<7>PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1d.7: debug port 1
<7>PCI: cache line size of 128 is not supported by device 0000:00:1d.7
<6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
<6>ehci_hcd 0000:00:1d.7: irq 209, io mem 0xfebff800
<6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb5: new device found, idVendor=0000, idProduct=0000
<6>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb5: Product: EHCI Host Controller
<6>usb usb5: Manufacturer: Linux 2.6.16.46-0.12-smp ehci_hcd
<6>usb usb5: SerialNumber: 0000:00:1d.7
<6>usb usb5: configuration #1 chosen from 1 choice
<6>hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 8 ports detected
<6>agpgart: Detected an Intel 865 Chipset.
<6>agpgart: AGP aperture is 64M @ 0xf8000000
<3>usb 1-1: device not accepting address 2, error -71
<6>device-mapper: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
<7>dm-netlink version 0.0.2 loaded
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>loop: loaded (max 8 devices)
<5>ReiserFS: sda3: found reiserfs format "3.6" with standard journal
<5>ReiserFS: sda3: using ordered data mode
<4>reiserfs: using flush barriers
<5>ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
<5>ReiserFS: sda3: checking transaction log (sda3)
<5>ReiserFS: sda3: Using r5 hash to sort names
<6>usb 5-1: new high speed USB device using ehci_hcd and address 2
<6>NTFS driver 2.1.26 [Flags: R/W MODULE].
<6>NTFS volume version 3.1.
<3>NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4000 encountered.
<3>NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows.
<6>usb 5-1: new device found, idVendor=03f0, idProduct=3217
<6>usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>usb 5-1: Product: HP LaserJet 3050
<6>usb 5-1: Manufacturer: Hewlett-Packard
<6>usb 5-1: SerialNumber: 00CNCK509647
<6>usb 5-1: configuration #1 chosen from 1 choice
<6>NTFS volume version 3.1.
<6>usb 5-4: new high speed USB device using ehci_hcd and address 4
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console (deleted)) at Mon Feb 18 20:39:33 2008
Configuring serial ports...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
/dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A
Configured serial ports
doneActivating swap-devices in /etc/fstab...
donedone
Starting udevd done
Loading required kernel modules
doneActivating device mapper...
done
Starting MD Raid done
Waiting for udev to settle...
Scanning for LVM volume groups...
Reading all physical volumes. This may take a while...
No volume groups found
No volume groups found
Activating LVM volume groups...
No volume groups found
done
Checking file systems...
fsck 1.38 (30-Jun-2005)
/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part3: Reiserfs super block in block 16 on /dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part3 of format 3.6 with standard journal
Blocks (total/free): 74993424/74941070 by 4096 bytes
Filesystem is clean
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda3 on /home type reiserfs (rw,acl,user_xattr)
/dev/hda1 on /windows/C type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8)
/dev/sdb1 on /windows/D type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8)
doneSetting up the hardware clockdone
Setting up hostname 'oxpa-desktop'done
Setting up loopback interface lo
lo IP address: 127.0.0.1/8
Checking for network time protocol daemon (NTPD): unused
Can't determine current runlevel
done
Creating /var/log/boot.msg
done<notice>killproc: kill(890,29)
Activating remaining swap-devices in /etc/fstab...
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
done
Enabling syn flood protectiondone
Disabling IP forwardingdone
done
Mounting securityfs on /sys/kernel/security done
Loading AppArmor module done
Loading AppArmor profiles done
done
System Boot Control: The system has been set up
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(890,3)
INIT: Entering runlevel: 5
Boot logging started on /dev/tty1(/dev/console) at Mon Feb 18 17:39:44 2008
<notice>startproc: execve (/usr/bin/dbus-daemon) [ /usr/bin/dbus-daemon --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/bin/dbus-daemon ]
<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0Master Resource Control: previous runlevel: N, switching to runlevel: 5
LC_ALL=POSIX apic=verbose INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ SPLASH=no splash=silent dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
done
Initializing random number generatordone
<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
Starting resource managerdone
<notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/acpid ]
[acpid]: starting up
[acpid]: 0 rules loaded
acpid: loading ACPI modules ( ac battery button ) done
acpid: will not skip unsupported modules
acpid: loading ACPI laptop modules ( ) done
Starting acpid done
Starting D-BUS daemondone
<notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes --retain-privileges ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/hald ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX apic=verbose INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ SPLASH=no splash=silent dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/klogd ]
Starting syslog servicesdone
Starting HAL daemondone
<notice>startproc: execve (/usr/sbin/dhcdbd) [ /usr/sbin/dhcdbd --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/dhcdbd ]
<notice>startproc: execve (/usr/sbin/NetworkManagerDispatcher) [ /usr/sbin/NetworkManagerDispatcher ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManagerDispatcher ]
<notice>startproc: execve (/usr/sbin/NetworkManager) [ /usr/sbin/NetworkManager ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManager ]
Starting the DHCP DBUS Daemondone
Starting the NetworkManagerDispatcherdone
Starting the NetworkManagerdone
If service network should wait until connection is established
then set /etc/sysconfig/network/config:NM_ONLINE_TIMEOUT
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -n ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/auditd ]
/etc/nam.conf does not exist
Starting auditd done
Loading keymap i386/qwerty/ru1.map.gz
doneLoading compose table winkeys shiftctrl latin1.adddone
Start Unicode mode
doneLoading console font Cyr_a8x16.psfu -m trivial G0:loadable
done<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/portmap ]
Starting RPC portmap daemondone
Importing Net File System (NFS)unused
Starting nfsboot (sm-notify) done
Mount SMB/ CIFS File Systems unused
<notice>startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ]
Starting irqbalance done
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/usr/bin/ionice DAEMON=/usr/sbin/cupsd ]
Checking/updating CPU microcode done
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
Starting Name Service Cache Daemondone
Starting cupsddone
<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
Starting SSH daemondone
Starting hotkey-setup done
<notice>startproc: execve (/usr/sbin/xinetd) [ /usr/sbin/xinetd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/xinetd ]
Starting ZENworks Management Daemondone
Starting mail service (Postfix)done
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
Starting CRON daemondone
Executing suseRegister (looking for new update channels): skipped
<notice>startproc: execve (/opt/gnome/sbin/gdm) [ /opt/gnome/sbin/gdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 apic=verbose KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= LANG=ru_RU.UTF-8 PREVLEVEL=N LINES=25 QT_SYSTEM_DIR=/usr/share/desktop-data HOME=/ SHLVL=2 XCURSOR_THEME=Industrial WINDOWMANAGER=/usr/X11R6/bin/gnome splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/opt/gnome/sbin/gdm ]
Starting INET services. (xinetd)done
Starting service gdmdone
<notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
Starting powersaved: done
<notice>checkproc: /opt/gnome/sbin/gdm 3095
i!
Master Resource Control: runlevel 5 has been reached
Skipped services in runlevel 5: namcd nfs smbfs splash suseRegister
<notice>killproc: kill(2302,3)
[/no]
[/more]
После установки SLED постоянно зависает: 10 минут, 20, пол часа... Всё равно встаёт намертво с горящей лампочкой чтения винта.
Вопрос, что это может быть? Куда копать? На текущий момент пробовал загружаться в failsafe режиме, но всё равно система подвисает.
конфигурация системы:
mb: ASUS P4P800-VM, биос перепрошил на 1018 версию чтоли.
3 винта: 1xIDE, 2xSATA + CD-ROM на IDE.
1256мб оперативки.
Гружусь с флешки на 4ГБ (далее она там "видна")
Пробовал играться настройками биоса, чтот не помогает.
далее /var/log/boot.msg
[more=boot.msg]
[no]
Inspecting /boot/System.map-2.6.16.46-0.12-smp
Loaded 22646 symbols from /boot/System.map-2.6.16.46-0.12-smp.
Symbols match kernel version 2.6.16.
No module symbols loaded - kernel modules not enabled.
klogd 1.4.1, log source = ksyslog started.
<5>Linux version 2.6.16.46-0.12-smp (geeko@buildhost) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) #1 SMP Thu May 17 14:00:09 UTC 2007
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000004ff30000 (usable)
<4> BIOS-e820: 000000004ff30000 - 000000004ff40000 (ACPI data)
<4> BIOS-e820: 000000004ff40000 - 000000004fff0000 (ACPI NVS)
<4> BIOS-e820: 000000004fff0000 - 0000000050000000 (reserved)
<4> BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
<5>383MB HIGHMEM available.
<5>895MB LOWMEM available.
<6>found SMP MP-table at 000ff780
<7>On node 0 totalpages: 327472
<7> DMA zone: 4096 pages, LIFO batch:0
<7> DMA32 zone: 0 pages, LIFO batch:0
<7> Normal zone: 225279 pages, LIFO batch:31
<7> HighMem zone: 98097 pages, LIFO batch:31
<6>DMI 2.3 present.
<3>Unknown genapic `apic=verbose' specified.
<6>Using APIC driver default
<7>ACPI: RSDP (v002 ACPIAM ) @ 0x000fad50
<7>ACPI: XSDT (v001 A M I OEMXSDT 0x09000505 MSFT 0x00000097) @ 0x4ff30100
<7>ACPI: FADT (v003 A M I OEMFACP 0x09000505 MSFT 0x00000097) @ 0x4ff30290
<7>ACPI: MADT (v001 A M I OEMAPIC 0x09000505 MSFT 0x00000097) @ 0x4ff30390
<7>ACPI: OEMB (v001 A M I OEMBIOS 0x09000505 MSFT 0x00000097) @ 0x4ff40040
<7>ACPI: DSDT (v001 PPVM1 PPVM1911 0x00000911 INTL 0x02002026) @ 0x00000000
<6>ACPI: PM-Timer IO Port: 0x808
<7>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>Processor #0 15:2 APIC version 20
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
<4>Processor #1 15:2 APIC version 20
<6>Overriding APIC driver with bigsmp
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
<7>ACPI: IRQ0 used by override.
<7>ACPI: IRQ2 used by override.
<7>ACPI: IRQ9 used by override.
<4>Enabling APIC mode: Physflat. Using 1 I/O APICs
<6>Using ACPI (MADT) for SMP configuration information
<4>Allocating PCI resources starting at 60000000 (gap: 50000000:afb80000)
<4>Built 1 zonelists
<5>Kernel command line: root=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 apic=verbose irqpoll apm=debug dmi=debug resume=/dev/sda1 splash=silent showopts
<4>Misrouted IRQ fixup and polling support enabled
<4>This may significantly impact system performance
<6>bootsplash: silent mode.
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Initializing CPU#0
<4>PID hash table entries: 4096 (order: 12, 65536 bytes)
<4>Detected 2394.330 MHz processor.
<6>Using tsc for high-res timesource
<4>Console: colour VGA+ 80x25
<4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory: 1290980k/1309888k available (1643k kernel code, 17536k reserved, 747k data, 196k init, 392388k highmem)
<4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>Calibrating delay using timer specific routine.. 4817.86 BogoMIPS (lpj=9635731)
<6>Security Framework v1.0.0 initialized
<4>Mount-cache hash table entries: 512
<7>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<7>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<7>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<6>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
<6>CPU0: Thermal monitoring enabled
<6>Checking 'hlt' instruction... OK.
<6>checking if image is initramfs... it is
<6>Freeing initrd memory: 2405k freed
<4> not found!
<4>CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
<4>enabled ExtINT on CPU#0
<4>Leaving ESR disabled.
<6>Enabling SMP...
<4>Booting processor 1/1 eip 3000
<6>Initializing CPU#1
<4>masked ExtINT on CPU#1
<4>Leaving ESR disabled.
<4>Calibrating delay using timer specific routine.. 4788.38 BogoMIPS (lpj=9576768)
<7>CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<7>CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<7>CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#1.
<6>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
<6>CPU1: Thermal monitoring enabled
<4>CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
<6>Total of 2 processors activated (9606.24 BogoMIPS).
<4>ENABLING IO-APIC IRQs
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
<6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 12353.2767 MHz.
<4>..... host bus clock speed is 1029.1896 MHz.
<6>checking TSC synchronization across 2 CPUs: passed.
<6>Enabling SMP...
<6>Brought up 2 CPUs
<4>migration_cost=74
<6>NET: Registered protocol family 16
<6>ACPI: bus type pci registered
<6>PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
<6>PCI: Using configuration type 1
<6>ACPI: Subsystem revision 20060127
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>PCI: Probing PCI hardware (bus 00)
<4>PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
<4>PCI quirk: region 0480-04bf claimed by ICH4 GPIO
<7>Boot video device is 0000:01:00.0
<4>PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
<6>PCI: Transparent bridge - 0000:00:1e.0
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 *14 15)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>pnp: PnP ACPI init
<6>pnp: PnP ACPI: found 14 devices
<6>PCI: Using ACPI for IRQ routing
<6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<7>number of MP IRQ sources: 15.
<7>number of IO-APIC #2 registers: 24.
<6>testing the IO APIC.......................
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>....... : physical APIC id: 02
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 000 00 1 0 0 0 0 0 0 39
<7> 02 000 00 0 0 0 0 0 0 0 31
<7> 03 000 00 1 0 0 0 0 0 0 41
<7> 04 000 00 1 0 0 0 0 0 0 49
<7> 05 001 01 0 0 0 0 0 0 0 51
<7> 06 000 00 1 0 0 0 0 0 0 59
<7> 07 001 01 0 0 0 0 0 0 0 61
<7> 08 000 00 1 0 0 0 0 0 0 69
<7> 09 001 01 0 1 0 0 0 0 0 71
<7> 0a 000 00 0 0 0 0 0 0 0 79
<7> 0b 001 01 0 0 0 0 0 0 0 81
<7> 0c 000 00 0 0 0 0 0 0 0 89
<7> 0d 000 00 1 0 0 0 0 0 0 91
<7> 0e 000 00 0 0 0 0 0 0 0 99
<7> 0f 001 01 0 0 0 0 0 0 0 A1
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<6>Using vector-based indexing
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<6>.................................... done.
<4>Setting up standard PCI resources
<6>pnp: 00:09: ioport range 0x680-0x6ff has been reserved
<6>pnp: 00:09: ioport range 0x290-0x297 has been reserved
<6>pnp: 00:0b: ioport range 0x3f6-0x3f6 has been reserved
<6>PCI: Bridge: 0000:00:01.0
<6> IO window: disabled.
<6> MEM window: fc900000-fe9fffff
<6> PREFETCH window: d7f00000-f7efffff
<6>PCI: Bridge: 0000:00:1e.0
<6> IO window: d000-dfff
<6> MEM window: fea00000-feafffff
<6> PREFETCH window: disabled.
<7>PCI: Setting latency timer of device 0000:00:1e.0 to 64
<6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
<6>apm: entry f000:ef50 cseg16 f000 dseg 40 cseg len ffff, dseg len 100 cseg16 len 0
<5>apm: disabled - APM is not SMP safe.
<6>audit: initializing netlink socket (disabled)
<5>audit(1203356367.768:1): initialized
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Initializing Cryptographic API
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Real Time Clock Driver v1.12ac
<6>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
<4>PNP: PS/2 controller doesn't have AUX irq; using default 12
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
<6>00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>mice: PS/2 mouse device common for all mice
<6>input: AT Translated Set 2 keyboard as /class/input/input0
<6>input: PC Speaker as /class/input/input1
<6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: bitmap version 4.39
<6>NET: Registered protocol family 2
<4>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<4>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<4>Using IPI No-Shortcut mode
<4>ACPI wakeup devices:
<4>P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K ILAN
<6>ACPI: (supports S0 S1 S3 S4 S5)
<6>Freeing unused kernel memory: 196k freed
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<5>SCSI subsystem initialized
<6>ICH5: IDE controller at PCI slot 0000:00:1f.1
<4>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
<6>ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
<6>ICH5: chipset revision 2
<6>ICH5: 100% native mode on irq 169
<6> ide0: BM-DMA at 0xef90-0xef97, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0xef98-0xef9f, BIOS settings: hdc:pio, hdd:DMA
<7>Probing IDE interface ide0...
<4>hda: QUANTUM FIREBALLP AS20.5, ATA DISK drive
<4>ide0 at 0xefe0-0xefe7,0xefae on irq 169
<6>hda: max request size: 128KiB
<6>hda: 40132503 sectors (20547 MB) w/1902KiB Cache, CHS=39813/16/63, UDMA(100)
<6>hda: cache flushes not supported
<6> hda: hda1
<7>Probing IDE interface ide1...
<4>hdd: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive
<4>ide1 at 0xefa0-0xefa7,0xefaa on irq 169
<7>libata version 2.00 loaded.
<7>ata_piix 0000:00:1f.2: version 2.00ac7
<6>ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
<6>ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>ata1: SATA max UDMA/133 cmd 0xEF88 ctl 0xEF86 bmdma 0xEE60 irq 169
<6>ata2: SATA max UDMA/133 cmd 0xEF68 ctl 0xEF82 bmdma 0xEE68 irq 169
<6>scsi0 : ata_piix
<6>ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
<6>ata1.00: ata1: dev 0 multi count 16
<6>ata1.00: configured for UDMA/133
<6>scsi1 : ata_piix
<6>ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
<6>ata2.00: ata2: dev 0 multi count 16
<6>ata2.00: configured for UDMA/133
<5> Vendor: ATA Model: ST3320620AS Rev: 3.AA
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<5>sda: Write Protect is off
<7>sda: Mode Sense: 00 3a 00 00
<5>SCSI device sda: drive cache: write back
<6> sda: sda1 sda2 sda3
<5>sd 0:0:0:0: Attached scsi disk sda
<5> Vendor: ATA Model: ST3320620AS Rev: 3.AA
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
<5>sdb: Write Protect is off
<7>sdb: Mode Sense: 00 3a 00 00
<5>SCSI device sdb: drive cache: write back
<5>SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
<5>sdb: Write Protect is off
<7>sdb: Mode Sense: 00 3a 00 00
<5>SCSI device sdb: drive cache: write back
<6> sdb: sdb1
<5>sd 1:0:0:0: Attached scsi disk sdb
<6>BIOS EDD facility v0.16 2004-Jun-25, 4 devices found
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>sd 1:0:0:0: Attached scsi generic sg1 type 0
<4>Attempting manual resume
<5>ReiserFS: sda2: found reiserfs format "3.6" with standard journal
<5>ReiserFS: sda2: using ordered data mode
<4>reiserfs: using flush barriers
<5>ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
<5>ReiserFS: sda2: checking transaction log (sda2)
<5>ReiserFS: sda2: Using r5 hash to sort names
<6>Adding 2104472k swap on /dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part1. Priority:-1 extents:1 across:2104472k
<6>hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
<6>Uniform CD-ROM driver Revision: 3.20
<6>e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
<6>e100: Copyright(c) 1999-2005 Intel Corporation
<6>ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 177
<6>e100: eth0: e100_probe: addr 0xfeaff000, irq 177, MAC addr 00:0C:6E:78:00:EE
<6>ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 185
<7>PCI: Setting latency timer of device 0000:00:1f.5 to 64
<6>usbcore: registered new driver usbfs
<6>usbcore: registered new driver hub
<6>USB Universal Host Controller Interface driver v2.3
<3>hw_random: RNG not detected
<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
<6>Linux agpgart interface v0.101 (c) Dave Jones
<6>intel8x0_measure_ac97_clock: measured 70529 usecs
<6>intel8x0: clocking to 48000
<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
<7>PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>uhci_hcd 0000:00:1d.0: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
<6>uhci_hcd 0000:00:1d.0: irq 193, io base 0x0000eec0
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: UHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb1: SerialNumber: 0000:00:1d.0
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
<7>PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
<6>uhci_hcd 0000:00:1d.1: irq 201, io base 0x0000ef00
<6>usb usb2: new device found, idVendor=0000, idProduct=0000
<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb2: Product: UHCI Host Controller
<6>usb usb2: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb2: SerialNumber: 0000:00:1d.1
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
<7>PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
<6>uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000ef20
<6>usb usb3: new device found, idVendor=0000, idProduct=0000
<6>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb3: Product: UHCI Host Controller
<6>usb usb3: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb3: SerialNumber: 0000:00:1d.2
<6>usb usb3: configuration #1 chosen from 1 choice
<6>hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 2 ports detected
<6>ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 193
<7>PCI: Setting latency timer of device 0000:00:1d.3 to 64
<6>uhci_hcd 0000:00:1d.3: UHCI Host Controller
<6>uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
<6>uhci_hcd 0000:00:1d.3: irq 193, io base 0x0000ef40
<6>usb usb4: new device found, idVendor=0000, idProduct=0000
<6>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb4: Product: UHCI Host Controller
<6>usb usb4: Manufacturer: Linux 2.6.16.46-0.12-smp uhci_hcd
<6>usb usb4: SerialNumber: 0000:00:1d.3
<6>usb usb4: configuration #1 chosen from 1 choice
<6>hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 2 ports detected
<6>usb 1-1: new full speed USB device using uhci_hcd and address 2
<6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209
<7>PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>ehci_hcd 0000:00:1d.7: debug port 1
<7>PCI: cache line size of 128 is not supported by device 0000:00:1d.7
<6>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
<6>ehci_hcd 0000:00:1d.7: irq 209, io mem 0xfebff800
<6>ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb5: new device found, idVendor=0000, idProduct=0000
<6>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb5: Product: EHCI Host Controller
<6>usb usb5: Manufacturer: Linux 2.6.16.46-0.12-smp ehci_hcd
<6>usb usb5: SerialNumber: 0000:00:1d.7
<6>usb usb5: configuration #1 chosen from 1 choice
<6>hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 8 ports detected
<6>agpgart: Detected an Intel 865 Chipset.
<6>agpgart: AGP aperture is 64M @ 0xf8000000
<3>usb 1-1: device not accepting address 2, error -71
<6>device-mapper: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
<7>dm-netlink version 0.0.2 loaded
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>loop: loaded (max 8 devices)
<5>ReiserFS: sda3: found reiserfs format "3.6" with standard journal
<5>ReiserFS: sda3: using ordered data mode
<4>reiserfs: using flush barriers
<5>ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
<5>ReiserFS: sda3: checking transaction log (sda3)
<5>ReiserFS: sda3: Using r5 hash to sort names
<6>usb 5-1: new high speed USB device using ehci_hcd and address 2
<6>NTFS driver 2.1.26 [Flags: R/W MODULE].
<6>NTFS volume version 3.1.
<3>NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4000 encountered.
<3>NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows.
<6>usb 5-1: new device found, idVendor=03f0, idProduct=3217
<6>usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>usb 5-1: Product: HP LaserJet 3050
<6>usb 5-1: Manufacturer: Hewlett-Packard
<6>usb 5-1: SerialNumber: 00CNCK509647
<6>usb 5-1: configuration #1 chosen from 1 choice
<6>NTFS volume version 3.1.
<6>usb 5-4: new high speed USB device using ehci_hcd and address 4
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console (deleted)) at Mon Feb 18 20:39:33 2008
Configuring serial ports...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
/dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A
Configured serial ports
doneActivating swap-devices in /etc/fstab...
donedone
Starting udevd done
Loading required kernel modules
doneActivating device mapper...
done
Starting MD Raid done
Waiting for udev to settle...
Scanning for LVM volume groups...
Reading all physical volumes. This may take a while...
No volume groups found
No volume groups found
Activating LVM volume groups...
No volume groups found
done
Checking file systems...
fsck 1.38 (30-Jun-2005)
/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part3: Reiserfs super block in block 16 on /dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part3 of format 3.6 with standard journal
Blocks (total/free): 74993424/74941070 by 4096 bytes
Filesystem is clean
donedone
Mounting local file systems...
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
debugfs on /sys/kernel/debug type debugfs (rw)
udev on /dev type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/sda3 on /home type reiserfs (rw,acl,user_xattr)
/dev/hda1 on /windows/C type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8)
/dev/sdb1 on /windows/D type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8)
doneSetting up the hardware clockdone
Setting up hostname 'oxpa-desktop'done
Setting up loopback interface lo
lo IP address: 127.0.0.1/8
Checking for network time protocol daemon (NTPD): unused
Can't determine current runlevel
done
Creating /var/log/boot.msg
done<notice>killproc: kill(890,29)
Activating remaining swap-devices in /etc/fstab...
doneSetting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
done
Enabling syn flood protectiondone
Disabling IP forwardingdone
done
Mounting securityfs on /sys/kernel/security done
Loading AppArmor module done
Loading AppArmor profiles done
done
System Boot Control: The system has been set up
System Boot Control: Running /etc/init.d/boot.local
done<notice>killproc: kill(890,3)
INIT: Entering runlevel: 5
Boot logging started on /dev/tty1(/dev/console) at Mon Feb 18 17:39:44 2008
<notice>startproc: execve (/usr/bin/dbus-daemon) [ /usr/bin/dbus-daemon --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/bin/dbus-daemon ]
<notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0Master Resource Control: previous runlevel: N, switching to runlevel: 5
LC_ALL=POSIX apic=verbose INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ SPLASH=no splash=silent dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/syslog-ng ]
done
Initializing random number generatordone
<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
Starting resource managerdone
<notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/acpid ]
[acpid]: starting up
[acpid]: 0 rules loaded
acpid: loading ACPI modules ( ac battery button ) done
acpid: will not skip unsupported modules
acpid: loading ACPI laptop modules ( ) done
Starting acpid done
Starting D-BUS daemondone
<notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes --retain-privileges ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/hald ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX apic=verbose INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=25 SHLVL=2 HOME=/ SPLASH=no splash=silent dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/klogd ]
Starting syslog servicesdone
Starting HAL daemondone
<notice>startproc: execve (/usr/sbin/dhcdbd) [ /usr/sbin/dhcdbd --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/dhcdbd ]
<notice>startproc: execve (/usr/sbin/NetworkManagerDispatcher) [ /usr/sbin/NetworkManagerDispatcher ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManagerDispatcher ]
<notice>startproc: execve (/usr/sbin/NetworkManager) [ /usr/sbin/NetworkManager ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 OLDPWD=/etc/sysconfig/network LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/NetworkManager ]
Starting the DHCP DBUS Daemondone
Starting the NetworkManagerDispatcherdone
Starting the NetworkManagerdone
If service network should wait until connection is established
then set /etc/sysconfig/network/config:NM_ONLINE_TIMEOUT
<notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -n ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/auditd ]
/etc/nam.conf does not exist
Starting auditd done
Loading keymap i386/qwerty/ru1.map.gz
doneLoading compose table winkeys shiftctrl latin1.adddone
Start Unicode mode
doneLoading console font Cyr_a8x16.psfu -m trivial G0:loadable
done<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/sbin/portmap ]
Starting RPC portmap daemondone
Importing Net File System (NFS)unused
Starting nfsboot (sm-notify) done
Mount SMB/ CIFS File Systems unused
<notice>startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ]
Starting irqbalance done
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/usr/bin/ionice DAEMON=/usr/sbin/cupsd ]
Checking/updating CPU microcode done
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
Starting Name Service Cache Daemondone
Starting cupsddone
<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
Starting SSH daemondone
Starting hotkey-setup done
<notice>startproc: execve (/usr/sbin/xinetd) [ /usr/sbin/xinetd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/xinetd ]
Starting ZENworks Management Daemondone
Starting mail service (Postfix)done
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 apic=verbose REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
Starting CRON daemondone
Executing suseRegister (looking for new update channels): skipped
<notice>startproc: execve (/opt/gnome/sbin/gdm) [ /opt/gnome/sbin/gdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 apic=verbose KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=80 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= LANG=ru_RU.UTF-8 PREVLEVEL=N LINES=25 QT_SYSTEM_DIR=/usr/share/desktop-data HOME=/ SHLVL=2 XCURSOR_THEME=Industrial WINDOWMANAGER=/usr/X11R6/bin/gnome splash=silent SPLASH=no dmi=debug ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_ST3320620AS_3QF05VNM-part2 _=/sbin/startproc DAEMON=/opt/gnome/sbin/gdm ]
Starting INET services. (xinetd)done
Starting service gdmdone
<notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ]
Starting powersaved: done
<notice>checkproc: /opt/gnome/sbin/gdm 3095
i!
Master Resource Control: runlevel 5 has been reached
Skipped services in runlevel 5: namcd nfs smbfs splash suseRegister
<notice>killproc: kill(2302,3)
[/no]
[/more]