» Проблема с Cisco 871

Добрый всем день!

Есть проблема, принесли циску 871 своял консольный кабель все оке соеденился.
При чем сразу оказался ROMMON безо всяких break клавиш.
вижу это

System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.

C870 series (Board ID: 3-148) platform with 131072 Kbytes of main memory

rommon 1 >

Далее почитал на разных форумах что надо IOS залить по TFTP

rommon 1 > set
PS1=rommon ! >
TFTP_TIMEOUT=800000
FE_SPEED_MODE=4
TFTP_RETRY_COUNT=20
ROM_PERSISTENT_UTC=1171539410
RET_2_RTS=14:36:50 MSK Thu Feb 15 2007
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1429781043
IP_ADDRESS=192.168.1.7
IP_SUBNET_MASK=255.255.0.0
DEFAULT_GATEWAY=192.168.1.1
TFTP_SERVER=192.168.1.2
TFTP_FILE=c870-advipservicesk9-mz.124-15.T3.bin
?=0
rommon 2 >
Все вроде оке ввожу tftpdnld

вижу это

IP_ADDRESS: 192.168.1.7
IP_SUBNET_MASK: 255.255.0.0
DEFAULT_GATEWAY: 192.168.1.1
TFTP_SERVER: 192.168.1.2
TFTP_FILE: c870-advipservicesk9-mz.124-15.T3.bin
Do you wish to continue? y/n: [n]: y

Receiving c870-advipservicesk9-mz.124-15.T3.bin from 192.168.1.2 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
File flash:/c870-advipservicesk9-mz.124-15.T3.bin already exists.
Deleting flash:/c870-advipservicesk9-mz.124-15.T3.bin before creating new file with same name.
Delete operation will take approximately 28 to 720 seconds
Writing flash:/c870-advipservicesk9-mz.124-15.T3.bin
Write operation will take approximately 115 to 345 seconds

после ожидания получаю это

rommon 4 >

и все, далее на всякий случай sync и ввожу boot и получаю это

Booting flash:/c870-advipservicesk9-mz.124-15.T3.bin
Self decompressing the image : ################################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version 12.4(15)T3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 25-Jan-08 09:59 by prod_rel_team
Image text-base: 0x8002007C, data-base: 0x81E739E0


Queued messages:
*Mar 1 00:00:11.547: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Mar 1 00:00:11.527: %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0]

The module in 0/-1/-1 in this router may not be a genuine
Cisco product. Cisco warranties and support programs only
apply to genuine Cisco products. If Cisco determines that
your insertion of non-Cisco memory, WIC cards, AIM cards,
Network Modules, SPA cards, GBICs or other modules into a
Cisco product is the cause of a support issue, Cisco may
deny support under your warranty or under a Cisco support
program such as SmartNet.


System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.

C870 series (Board ID: 3-148) platform with 131072 Kbytes of main memory

rommon 1 >

и далее ничего большего, команда dir

rommon 1 > dir

List of filesystems currently registered:

flash[0]: (read-write)

что еще мне делать я не знаю,
Опишите подробно как и что делать с командами для ввода через copy

Заранее благодарен

Возможен вариант с битым ИОСом. format flash: и заливаем заново.
dir flash:
для просмотра содержимого флешки

да я уже 8 IOS опробывал ничего нового. что делать,

меня смущает вот это

Queued messages:
*Mar 1 00:00:10.103: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Mar 1 00:00:10.067: %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0]

The module in 0/-1/-1 in this router may not be a genuine
Cisco product. Cisco warranties and support programs only
apply to genuine Cisco products. If Cisco determines that
your insertion of non-Cisco memory, WIC cards, AIM cards,
Network Modules, SPA cards, GBICs or other modules into a
Cisco product is the cause of a support issue, Cisco may
deny support under your warranty or under a Cisco support
program such as SmartNet.

что это???????????

Добавлено:
ПРОБЛЕМА РЕШЕНА

версия прошивки не та была

System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE

поставилась только Version 12.3(8r)YI3

Та же беда.
Поделись прошивкой или дай ссылку плиз.

SnooperDmitri
Как поменял прошивку???

Kuruan Циска в режиме rommon позволяет залить прошивку через х-модем или tftp.

Код: rommon 3 > set
PS1=rommon ! >
IP_ADDRESS=172.18.16.76
IP_SUBNET_MASK=255.255.255.192
DEFAULT_GATEWAY=172.18.16.65
TFTP_SERVER=172.18.16.2
TFTP_FILE=c870-advipservicesk9-mz.124-15.T3.bin
The variables to set for tftpdnld are shown here:

usage: tftpdnld [-ur]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.

The following variables are REQUIRED to be set for tftpdnld:
IP_ADDRESS: The IP address for this unit
IP_SUBNET_MASK: The subnet mask for this unit
DEFAULT_GATEWAY: The default gateway for this unit
TFTP_SERVER: The IP address of the server to fetch from
TFTP_FILE: The filename to fetch

The following variables are OPTIONAL:
TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7)
TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)

Command line options:
-r: do not write flash, load to DRAM only and launch image
-u: upgrade the rommon, system will reboot once upgrade is complete
rommon 14 >