Добрый вечер всем пользователям форума.Долго боролся с Гуглом,пытаясь скачать софт для восстановления OCZ Deneva 2C-потерпел поражение.Так вот может найдется добрый победитель и зальет на GoogleDrive или Mail.ru-облако FW_PPRO_5_8_2_Release.906190.release-пакет с прошивками и FW_Worksheet_SFI_SF-2000_140120_Confidential_Gold-таблицу,да поделится ссылкой в личку???Буду признателен,уж очень хочется его восстановить.
» Ремонт SSD накопителей на контроллерах SandForce
Огромное спасибо за помощь.Таблицу стянул,а вот пакет с прошивками только за Злотые дают скачать (.Так-что вопрос актуален...
svarnoy80
А что, предыдущие ссылки не катят?
А что, предыдущие ссылки не катят?
Progaks
Ранее писали, правда на кингстоне, но на том же SF2281 помогло включение Write Protect в конфиге.
Цитата:
В запрошенных облаках вроде никто не выкладывал.
svarnoy80
Смотри личку.
Ранее писали, правда на кингстоне, но на том же SF2281 помогло включение Write Protect в конфиге.
Цитата:
А что, предыдущие ссылки не катят?
В запрошенных облаках вроде никто не выкладывал.
svarnoy80
Смотри личку.
[more] Stanchick спс процесс пошёл дальше
но уже вылезла другая ошибка
[Sun 02/28/2016 23:17:20] - FORMAT command completed...
[Sun 02/28/2016 23:17:20] - Waiting (2 sec) for the drive to settle...
[Sun 02/28/2016 23:17:22] - Setting up the stamp information through CDU command...
[Sun 02/28/2016 23:17:22] - FATAL_ERROR: Could not perform the ReadDriveConfigUnique() operation on the drive... (0x12000004:SF_SG_HOST_BAD_TARGET_ERROR)
[Sun 02/28/2016 23:17:22] - End of Genesis manufacturing log.
[Sun 02/28/2016 23:17:22] - Exiting...
решил добавить ещё лог с терминала
<MFB> Advanced FLASH test not supported for CFG_FLASH_MODE_TMI_ASYNC devices
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
Security: Disabled
H/w Decode enabled
<MFB>
*** MFB 522 Sep 27 2013 16:14:08 B:FW_PPRO_5_2_1_20130924:FW_PPRO_5_2_2_Release-
672199 ***
*** Config cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S ***
*** Chip RevId from HW: B01 (ID=288571), FW Targeted For: B02 ASIC ****** SysClk
: 300 MHz
*** Packer : 500 MHz
*** Flash : 800 MHz
*** FlaDiv : 6
<MFB> *** TMI_TS : 2
<MFB>
*** GPIO0 : 1
<MFB> Scap charge wait
<MFB> Scap charge done
<MFB User> libSfStartC enter cfg:3fff3e38
<MFB> Flash Rblock Test on 0 - bus:2 ce:2 die:1 lane:4 pageCnt:1 correctPwr:128
seed:dead1390 markers:2000
Errors in BUS:0 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0022, LANE 2: 0002, LAN
E 3: 0002, <MFB> ]
Errors in BUS:1 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
Errors in BUS:0 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0003, LANE 2: 0002, LAN
E 3: 0022, <MFB> ]
Errors in BUS:1 CE: 1 DIE:0 [ LANE 0: 0003, LANE 1: 0042, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
<MFB> Special Bad Block Scan: Valid 0 NumBytes 448 numOnes 1
<MFB> Read Device ID: 2C 88 04 4B A9 00
<MFB> == Format mode ONE align 0 ==
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> Flash ID Check
<MFB> Creating New Root
<MFB> Bad Block Discovery ...
<MFB> Number of Bad Blocks for SE/plane/lane
<MFB> SE pl: ln0 ln1 ln2 ln3
<MFB> 0 0: 1 1 1 1
<MFB> 0 1: 1 1 1 1
<MFB> 1 0: 1 1 1 1
<MFB> 1 1: 1 1 2 1
<MFB> 2 0: 1 1 1 1
<MFB> 2 1: 1 1 1 1
<MFB> 3 0: 1 1 1 1
<MFB> 3 1: 1 1 1 1
<MFB> Total Bad Block number is: 33 out of 65536
<MFB> Added donor[0]= 45
<MFB> Added donor[1]= 1335
<MFB> Enabling Remap Unit...
<MFB> Erasing All Virgin Blocks...
<MFB> No Host GDL!
<MFB> Creating the Root Record ...
<MFB> Input PE: 0
<MFB> Drive RDD:100000 RDD Low:100000, PE: 3000 Options:0004 Warranty: 0
<MFB> Format: WP Circuit Present (dynamic)
<MFB> CreateAndVerifyRoot: fid=2 ibidx=6 buf=3fff007c buflen=3876
<MFB> CreateAndVerifyRoot: fid=2 ibidx=7 buf=3fff007c buflen=3876
<MFB> CreateAndVerifyRoot: fid=1 ibidx=2 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=3 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=4 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=5 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=0 ibidx=0 buf=3fff10fc buflen=3876
<MFB> CreateAndVerifyRoot: fid=0 ibidx=1 buf=3fff10fc buflen=3876
<MFB> Initialize the Root ...
<MFB> PPRO-15147 (LION-1540): Retired Root IBlocks=0.
Found a valid Config Record.
Bus Width [bits] = 32
Number of CE = 2
Number of Die / CE = 1
CE CFG (Bus Mode) = 2-DIMM
Number of Bus = 2
Flash Page Size = 8192
Flash Page / Block = 256
Number of Block / Die = 2048
E-Page Size = 512
ECC Bytes = 27
ECC Correction Power = 16
<MFB> Low PE Flashware File Feature : NO
<MFB> Coalesce Compression Feature : YES
<MFB> Single Plane Remap Feature : YES
<MFB> RootInit: WP Circuit Present (dynamic)
<MFB> EVT LOG. Panic Dump slot 0 epa 0x00020002
<MFB> EVT LOG. Panic Dump slot 1 epa 0x20020002
<MFB> EVT LOG. Panic Dump slot 2 epa 0x00020082
<MFB> EVT LOG. Panic Dump slot 3 epa 0x20020082
<MFB> ------> Root Record Versions: CONFIG=1, PRR=1 (ib=3,pp=1), SRR=1 (ib=7,pp=
1) <------
<MFB> Saving Bad Block List ...
<MFB> Saving Grown Defect List ...
<MFB> Initializing SMART root file ...
<MFB> InitSmartLogRootFile is done
<MFB> Initializing XTS Global Keys ...
<MFB> Initializing Life Table ...
<MFB> Saving Life Table ...
<MFB> Set LBA Offset to 0 ...
<MFB> Clearing the Map Table ...
<MFB> Clearing the SIN Table ...
<MFB> Saving the MAP Table1 ...
<MFB> Saving the MAP Table2 ...
<MFB> Saving the SIN Table ...
<MFB> Saving the Remap Table ...
---> SAVE REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes 2 ticks <---
<MFB> Verifying the Remap Table ...
---> LOAD REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes, 1 ticks, 0 remapped <---
<MFB [/more]
но уже вылезла другая ошибка
[Sun 02/28/2016 23:17:20] - FORMAT command completed...
[Sun 02/28/2016 23:17:20] - Waiting (2 sec) for the drive to settle...
[Sun 02/28/2016 23:17:22] - Setting up the stamp information through CDU command...
[Sun 02/28/2016 23:17:22] - FATAL_ERROR: Could not perform the ReadDriveConfigUnique() operation on the drive... (0x12000004:SF_SG_HOST_BAD_TARGET_ERROR)
[Sun 02/28/2016 23:17:22] - End of Genesis manufacturing log.
[Sun 02/28/2016 23:17:22] - Exiting...
решил добавить ещё лог с терминала
<MFB> Advanced FLASH test not supported for CFG_FLASH_MODE_TMI_ASYNC devices
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
Security: Disabled
H/w Decode enabled
<MFB>
*** MFB 522 Sep 27 2013 16:14:08 B:FW_PPRO_5_2_1_20130924:FW_PPRO_5_2_2_Release-
672199 ***
*** Config cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S ***
*** Chip RevId from HW: B01 (ID=288571), FW Targeted For: B02 ASIC ****** SysClk
: 300 MHz
*** Packer : 500 MHz
*** Flash : 800 MHz
*** FlaDiv : 6
<MFB> *** TMI_TS : 2
<MFB>
*** GPIO0 : 1
<MFB> Scap charge wait
<MFB> Scap charge done
<MFB User> libSfStartC enter cfg:3fff3e38
<MFB> Flash Rblock Test on 0 - bus:2 ce:2 die:1 lane:4 pageCnt:1 correctPwr:128
seed:dead1390 markers:2000
Errors in BUS:0 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0022, LANE 2: 0002, LAN
E 3: 0002, <MFB> ]
Errors in BUS:1 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
Errors in BUS:0 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0003, LANE 2: 0002, LAN
E 3: 0022, <MFB> ]
Errors in BUS:1 CE: 1 DIE:0 [ LANE 0: 0003, LANE 1: 0042, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
<MFB> Special Bad Block Scan: Valid 0 NumBytes 448 numOnes 1
<MFB> Read Device ID: 2C 88 04 4B A9 00
<MFB> == Format mode ONE align 0 ==
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> Flash ID Check
<MFB> Creating New Root
<MFB> Bad Block Discovery ...
<MFB> Number of Bad Blocks for SE/plane/lane
<MFB> SE pl: ln0 ln1 ln2 ln3
<MFB> 0 0: 1 1 1 1
<MFB> 0 1: 1 1 1 1
<MFB> 1 0: 1 1 1 1
<MFB> 1 1: 1 1 2 1
<MFB> 2 0: 1 1 1 1
<MFB> 2 1: 1 1 1 1
<MFB> 3 0: 1 1 1 1
<MFB> 3 1: 1 1 1 1
<MFB> Total Bad Block number is: 33 out of 65536
<MFB> Added donor[0]= 45
<MFB> Added donor[1]= 1335
<MFB> Enabling Remap Unit...
<MFB> Erasing All Virgin Blocks...
<MFB> No Host GDL!
<MFB> Creating the Root Record ...
<MFB> Input PE: 0
<MFB> Drive RDD:100000 RDD Low:100000, PE: 3000 Options:0004 Warranty: 0
<MFB> Format: WP Circuit Present (dynamic)
<MFB> CreateAndVerifyRoot: fid=2 ibidx=6 buf=3fff007c buflen=3876
<MFB> CreateAndVerifyRoot: fid=2 ibidx=7 buf=3fff007c buflen=3876
<MFB> CreateAndVerifyRoot: fid=1 ibidx=2 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=3 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=4 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=1 ibidx=5 buf=3fff0064 buflen=24
<MFB> CreateAndVerifyRoot: fid=0 ibidx=0 buf=3fff10fc buflen=3876
<MFB> CreateAndVerifyRoot: fid=0 ibidx=1 buf=3fff10fc buflen=3876
<MFB> Initialize the Root ...
<MFB> PPRO-15147 (LION-1540): Retired Root IBlocks=0.
Found a valid Config Record.
Bus Width [bits] = 32
Number of CE = 2
Number of Die / CE = 1
CE CFG (Bus Mode) = 2-DIMM
Number of Bus = 2
Flash Page Size = 8192
Flash Page / Block = 256
Number of Block / Die = 2048
E-Page Size = 512
ECC Bytes = 27
ECC Correction Power = 16
<MFB> Low PE Flashware File Feature : NO
<MFB> Coalesce Compression Feature : YES
<MFB> Single Plane Remap Feature : YES
<MFB> RootInit: WP Circuit Present (dynamic)
<MFB> EVT LOG. Panic Dump slot 0 epa 0x00020002
<MFB> EVT LOG. Panic Dump slot 1 epa 0x20020002
<MFB> EVT LOG. Panic Dump slot 2 epa 0x00020082
<MFB> EVT LOG. Panic Dump slot 3 epa 0x20020082
<MFB> ------> Root Record Versions: CONFIG=1, PRR=1 (ib=3,pp=1), SRR=1 (ib=7,pp=
1) <------
<MFB> Saving Bad Block List ...
<MFB> Saving Grown Defect List ...
<MFB> Initializing SMART root file ...
<MFB> InitSmartLogRootFile is done
<MFB> Initializing XTS Global Keys ...
<MFB> Initializing Life Table ...
<MFB> Saving Life Table ...
<MFB> Set LBA Offset to 0 ...
<MFB> Clearing the Map Table ...
<MFB> Clearing the SIN Table ...
<MFB> Saving the MAP Table1 ...
<MFB> Saving the MAP Table2 ...
<MFB> Saving the SIN Table ...
<MFB> Saving the Remap Table ...
---> SAVE REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes 2 ticks <---
<MFB> Verifying the Remap Table ...
---> LOAD REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes, 1 ticks, 0 remapped <---
<MFB [/more]
это опять я... пробую прошивки ... нет ни у кого такой: 22818 SF-2281-Gold SF-2281-Gold 60GB Micron25 MLC TSOP 16xMT29F32G08CBACAWP (RAISE OFF)
GARRYGUDINI2102
22220
22241
22797
22818
27189
Они все есть в FW_5.2.2
22220
22241
22797
22818
27189
Они все есть в FW_5.2.2
GARRYGUDINI2102
Цитата:
держи https://yadi.sk/d/NRELQZiZpoJon
Цитата:
нет ни у кого такой: 22818 SF-2281-Gold SF-2281-Gold 60GB Micron25 MLC TSOP 16xMT29F32G08CBACAWP (RAISE OFF)
держи https://yadi.sk/d/NRELQZiZpoJon
Progaks Из лога: <MFB> Read Device ID: 2C 88 04 4B A9 00 что есть MT29F64G08CBAAAWP или MT29F128G08AJAAA но не: *** Config cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S ***
snip45
на плате именно MT29F64G08CBAAA
на плате именно MT29F64G08CBAAA
Цитата:
на плате именно MT29F64G08CBAAAНу так 22189 из доступного должно подойти. В логе MT29F128G08CFAAAWP,предположу,что файл переименован случайно был (из 22193 например). Микры не совместимы.
[liveuser@localhost ~]$ su
[root@localhost liveuser]# lsscsi
[0:0:0:0] disk ATA SandForce{200026 20DA /dev/sda
[1:0:0:0] cd/dvd TSSTcorp CDDVDW SN-208AB TO03 /dev/sr0
[6:0:0:0] disk Single Flash Reader 1.00 /dev/sdb
[7:0:0:0] disk UFD 3.0 Silicon-Power16G 1.00 /dev/sdc
[12:0:0:0] disk Sony MSAC-UAM2 1.00 /dev/sdf
[13:0:0:0] disk UFD 2.0 Silicon-Power32G PMAP /dev/sde
[root@localhost liveuser]# /home/liveuser/SF_Genesis -PROCESS_SSD 0:0:0:0 /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig 12345 www_123 log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 18:32:37] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
argv[4]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 18:32:37] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
[Tue 03/01/2016 18:32:43] - Issuing a discovery command for device: '0:0:0:0'
[Tue 03/01/2016 18:34:43] - Discovery command completed...
[Tue 03/01/2016 18:34:43] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 18:34:48] - End of Genesis manufacturing log.
[Tue 03/01/2016 18:34:48] - Exiting...
[Tue 03/01/2016 18:34:48] - Overall Result for Device: ****** FAIL ******
что то опять не так подскажите!!!
Добавлено:
вот что получил сейчас буду смотреть диск
[liveuser@localhost ~]$ su
[root@localhost liveuser]# lsscsi
[0:0:0:0] disk ATA SandForce{200026 20DA /dev/sda
[1:0:0:0] cd/dvd TSSTcorp CDDVDW SN-208AB TO03 /dev/sr0
[6:0:0:0] disk UFD 2.0 Silicon-Power32G PMAP /dev/sdb
[7:0:0:0] disk Single Flash Reader 1.00 /dev/sdc
[root@localhost liveuser]# /home/liveuser/SF_Genesis -PROCESS_SSD 0:0:0:0 /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig 12345 www_123 log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:24] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
argv[4]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:24] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
[Tue 03/01/2016 19:44:29] - Issuing a discovery command for device: '0:0:0:0'
[Tue 03/01/2016 19:44:34] - Discovery command completed...
[Tue 03/01/2016 19:44:34] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 19:44:39] - Device designation string '0:0:0:0' is mapped to node '/dev/sg0'
[Tue 03/01/2016 19:44:39] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg0
MFP Package Filename = /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
Configuration File = /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
Serial No. = 12345
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:39] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:44:39] - Validating Manufacturing Firmware Package: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
[Tue 03/01/2016 19:45:05] - Successfully opened the package: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
[Tue 03/01/2016 19:45:05] - file /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig Loaded successfully
[Tue 03/01/2016 19:45:05] - Warning: Unable to query diagnostics information to perform power management settings check
[Tue 03/01/2016 19:45:05] - B01 Power Management configuration request detected
[Tue 03/01/2016 19:45:05] - Successfully extracted *.DriveConfig file: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
[Tue 03/01/2016 19:45:05] - Extracted Config_ID: 1 (22818) in DriveConfig file: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
[Tue 03/01/2016 19:45:05] - Extracted SerialOutputControl: 0
[Tue 03/01/2016 19:45:05] - Searching for flashware image for configuration 22818
[Tue 03/01/2016 19:45:05] - Manifest found for configuration 22818
[Tue 03/01/2016 19:45:05] - Flashware image extracted: 22818_fw_cl_mlc_Micron_32Gb_MT29F128G08CBACAWP_2Q_2C_1D_S_PP_R00755_s512.vic
[Tue 03/01/2016 19:45:05] - Searching for manufacturing image for configuration 22818
[Tue 03/01/2016 19:45:05] - Manifest found for configuration 22818
[Tue 03/01/2016 19:45:05] - Manufacturing image extracted: 22818_mf_mlc_Micron_32Gb_MT29F128G08CBACAWP_2Q_2C_1D_S_PP_R00755_s512.vic
[Tue 03/01/2016 19:45:05] - Proceeding in ROM mode, download feature 3...
[Tue 03/01/2016 19:45:05] - Successfully downloaded MFB to the drive...
[Tue 03/01/2016 19:45:05] - Waiting (5 sec) for the drive to settle...
[Tue 03/01/2016 19:45:10] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:45:10] - Firmware revision reported to be: '522ABBM0'. This indicates MFB download was successful.
[Tue 03/01/2016 19:45:10] - Successfully enabled SMART capabilities...
[Tue 03/01/2016 19:45:12] - Successfully issued a diagnostic unlock...
[Tue 03/01/2016 19:45:13] - Performing the flash test of block 0 (0x0000)...
[Tue 03/01/2016 19:45:15] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 1 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 2 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 16
Number of failures: 0
Number of Passed with warnings: 14
No. Passed without warnings: 2
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:45:15] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 117231408
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 26668 (0x682C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:45:49] - FORMAT command completed...
[Tue 03/01/2016 19:45:49] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 19:45:51] - Setting up the stamp information through CDU command...
[Tue 03/01/2016 19:45:54] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 19:45:56] - Downloading the flashware to the drive... feature 3
[Tue 03/01/2016 19:45:58] - Successfully downloaded flashware to the drive...
[Tue 03/01/2016 19:45:58] - Waiting (15 sec) for the drive to settle...
[Tue 03/01/2016 19:46:13] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:46:13] - Firmware revision reported to be: '522ABBF0'
[Tue 03/01/2016 19:46:13] - Enabling SMART support...
[Tue 03/01/2016 19:46:13] - Issuing a diagnostic unlock to the drive...
[Tue 03/01/2016 19:46:15] - Setting up Max LBA settings...
[Tue 03/01/2016 19:46:18] - Change of sector size is not required, sector size is already set to 512
[Tue 03/01/2016 19:46:19] - Setting the serial number of the drive to: 12345
[Tue 03/01/2016 19:46:22] - Setting the World Wide Name (WWN) of the drive to: www_123
[Tue 03/01/2016 19:46:25] - Processing completed for device: 12345
[Tue 03/01/2016 19:46:25] - Begin collecting the device post-process log/information
[Tue 03/01/2016 19:46:25] - Creating the Log Bundle...
[Tue 03/01/2016 19:46:25] - Plain text identify log created
[Tue 03/01/2016 19:46:26] - Plain text diagnostics identify log created
[Tue 03/01/2016 19:46:27] - Plain text diagnostics information log created
[Tue 03/01/2016 19:46:28] - Plain text format information log created
[Tue 03/01/2016 19:46:28] - Plain text SMART log created
[Tue 03/01/2016 19:46:29] - Plain text manufacturing defect list log created
[Tue 03/01/2016 19:46:31] - Plain text grown defect list log created
[Tue 03/01/2016 19:46:32] - Plain text panic directory listing log created
[Tue 03/01/2016 19:46:32] - Completed collecting all plain text log files.
[Tue 03/01/2016 19:46:32] - End of logs and information collection
[Tue 03/01/2016 19:46:33] - Applying the remaining ConfigUniqueDrive settings...
[Tue 03/01/2016 19:46:34] - Setting Customer ID with value : 0
[Tue 03/01/2016 19:46:34] - Setting Device Nominal Form Factor with value : 3
[Tue 03/01/2016 19:46:34] - Setting Diagnostic Unlock Key with value supplied
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 4096 Plus DIFF Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 4096 Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 512B Plus DIFF Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 512B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 520B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 524B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 528B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Model No. with value : CORSAIR 60GB
[Tue 03/01/2016 19:46:34] - Setting Power Management Version with value : 0
[Tue 03/01/2016 19:46:34] - Setting Serial Number with value : 1234567890
[Tue 03/01/2016 19:46:34] - Total of 1 valid MaxLBA settings were setup to be written to the drive.
[Tue 03/01/2016 19:46:36] - Successfully applied the remaining ConfigUniqueDrive settings...
[Tue 03/01/2016 19:46:36] - Issuing an IdleImmediate command to the drive...
[Tue 03/01/2016 19:46:36] - Not an Enterprise drive,so, continuing without setting master password..
[Tue 03/01/2016 19:46:36] - End of Genesis manufacturing log.
[Tue 03/01/2016 19:46:36] - Exiting...
[Tue 03/01/2016 19:46:36] - Overall Result for Device: /dev/sg0 ****** PASS ******
[root@localhost liveuser]# lsscsi
[0:0:0:0] disk ATA SandForce{200026 20DA /dev/sda
[1:0:0:0] cd/dvd TSSTcorp CDDVDW SN-208AB TO03 /dev/sr0
[6:0:0:0] disk Single Flash Reader 1.00 /dev/sdb
[7:0:0:0] disk UFD 3.0 Silicon-Power16G 1.00 /dev/sdc
[12:0:0:0] disk Sony MSAC-UAM2 1.00 /dev/sdf
[13:0:0:0] disk UFD 2.0 Silicon-Power32G PMAP /dev/sde
[root@localhost liveuser]# /home/liveuser/SF_Genesis -PROCESS_SSD 0:0:0:0 /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig 12345 www_123 log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 18:32:37] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
argv[4]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 18:32:37] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
[Tue 03/01/2016 18:32:43] - Issuing a discovery command for device: '0:0:0:0'
[Tue 03/01/2016 18:34:43] - Discovery command completed...
[Tue 03/01/2016 18:34:43] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 18:34:48] - End of Genesis manufacturing log.
[Tue 03/01/2016 18:34:48] - Exiting...
[Tue 03/01/2016 18:34:48] - Overall Result for Device: ****** FAIL ******
что то опять не так подскажите!!!
Добавлено:
вот что получил сейчас буду смотреть диск
[liveuser@localhost ~]$ su
[root@localhost liveuser]# lsscsi
[0:0:0:0] disk ATA SandForce{200026 20DA /dev/sda
[1:0:0:0] cd/dvd TSSTcorp CDDVDW SN-208AB TO03 /dev/sr0
[6:0:0:0] disk UFD 2.0 Silicon-Power32G PMAP /dev/sdb
[7:0:0:0] disk Single Flash Reader 1.00 /dev/sdc
[root@localhost liveuser]# /home/liveuser/SF_Genesis -PROCESS_SSD 0:0:0:0 /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig 12345 www_123 log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:24] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
argv[4]: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/Results_Test_PackageManager.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:24] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
[Tue 03/01/2016 19:44:29] - Issuing a discovery command for device: '0:0:0:0'
[Tue 03/01/2016 19:44:34] - Discovery command completed...
[Tue 03/01/2016 19:44:34] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 19:44:39] - Device designation string '0:0:0:0' is mapped to node '/dev/sg0'
[Tue 03/01/2016 19:44:39] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg0
MFP Package Filename = /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
Configuration File = /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
Serial No. = 12345
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:44:39] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:44:39] - Validating Manufacturing Firmware Package: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
[Tue 03/01/2016 19:45:05] - Successfully opened the package: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/FW_PPRO_5_2_2_Release.672199.release.0.mfp
[Tue 03/01/2016 19:45:05] - file /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig Loaded successfully
[Tue 03/01/2016 19:45:05] - Warning: Unable to query diagnostics information to perform power management settings check
[Tue 03/01/2016 19:45:05] - B01 Power Management configuration request detected
[Tue 03/01/2016 19:45:05] - Successfully extracted *.DriveConfig file: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
[Tue 03/01/2016 19:45:05] - Extracted Config_ID: 1 (22818) in DriveConfig file: /media/SP32/FW_PPRO_5_2_2_Release.672199.release--0/22818.0.driveconfig
[Tue 03/01/2016 19:45:05] - Extracted SerialOutputControl: 0
[Tue 03/01/2016 19:45:05] - Searching for flashware image for configuration 22818
[Tue 03/01/2016 19:45:05] - Manifest found for configuration 22818
[Tue 03/01/2016 19:45:05] - Flashware image extracted: 22818_fw_cl_mlc_Micron_32Gb_MT29F128G08CBACAWP_2Q_2C_1D_S_PP_R00755_s512.vic
[Tue 03/01/2016 19:45:05] - Searching for manufacturing image for configuration 22818
[Tue 03/01/2016 19:45:05] - Manifest found for configuration 22818
[Tue 03/01/2016 19:45:05] - Manufacturing image extracted: 22818_mf_mlc_Micron_32Gb_MT29F128G08CBACAWP_2Q_2C_1D_S_PP_R00755_s512.vic
[Tue 03/01/2016 19:45:05] - Proceeding in ROM mode, download feature 3...
[Tue 03/01/2016 19:45:05] - Successfully downloaded MFB to the drive...
[Tue 03/01/2016 19:45:05] - Waiting (5 sec) for the drive to settle...
[Tue 03/01/2016 19:45:10] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:45:10] - Firmware revision reported to be: '522ABBM0'. This indicates MFB download was successful.
[Tue 03/01/2016 19:45:10] - Successfully enabled SMART capabilities...
[Tue 03/01/2016 19:45:12] - Successfully issued a diagnostic unlock...
[Tue 03/01/2016 19:45:13] - Performing the flash test of block 0 (0x0000)...
[Tue 03/01/2016 19:45:15] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 1 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 2 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 16
Number of failures: 0
Number of Passed with warnings: 14
No. Passed without warnings: 2
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:45:15] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 117231408
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 26668 (0x682C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 19:45:49] - FORMAT command completed...
[Tue 03/01/2016 19:45:49] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 19:45:51] - Setting up the stamp information through CDU command...
[Tue 03/01/2016 19:45:54] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 19:45:56] - Downloading the flashware to the drive... feature 3
[Tue 03/01/2016 19:45:58] - Successfully downloaded flashware to the drive...
[Tue 03/01/2016 19:45:58] - Waiting (15 sec) for the drive to settle...
[Tue 03/01/2016 19:46:13] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 19:46:13] - Firmware revision reported to be: '522ABBF0'
[Tue 03/01/2016 19:46:13] - Enabling SMART support...
[Tue 03/01/2016 19:46:13] - Issuing a diagnostic unlock to the drive...
[Tue 03/01/2016 19:46:15] - Setting up Max LBA settings...
[Tue 03/01/2016 19:46:18] - Change of sector size is not required, sector size is already set to 512
[Tue 03/01/2016 19:46:19] - Setting the serial number of the drive to: 12345
[Tue 03/01/2016 19:46:22] - Setting the World Wide Name (WWN) of the drive to: www_123
[Tue 03/01/2016 19:46:25] - Processing completed for device: 12345
[Tue 03/01/2016 19:46:25] - Begin collecting the device post-process log/information
[Tue 03/01/2016 19:46:25] - Creating the Log Bundle...
[Tue 03/01/2016 19:46:25] - Plain text identify log created
[Tue 03/01/2016 19:46:26] - Plain text diagnostics identify log created
[Tue 03/01/2016 19:46:27] - Plain text diagnostics information log created
[Tue 03/01/2016 19:46:28] - Plain text format information log created
[Tue 03/01/2016 19:46:28] - Plain text SMART log created
[Tue 03/01/2016 19:46:29] - Plain text manufacturing defect list log created
[Tue 03/01/2016 19:46:31] - Plain text grown defect list log created
[Tue 03/01/2016 19:46:32] - Plain text panic directory listing log created
[Tue 03/01/2016 19:46:32] - Completed collecting all plain text log files.
[Tue 03/01/2016 19:46:32] - End of logs and information collection
[Tue 03/01/2016 19:46:33] - Applying the remaining ConfigUniqueDrive settings...
[Tue 03/01/2016 19:46:34] - Setting Customer ID with value : 0
[Tue 03/01/2016 19:46:34] - Setting Device Nominal Form Factor with value : 3
[Tue 03/01/2016 19:46:34] - Setting Diagnostic Unlock Key with value supplied
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 4096 Plus DIFF Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 4096 Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 512B Plus DIFF Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 512B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 520B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 524B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Max LBA Count for 528B Sectors with value : 0
[Tue 03/01/2016 19:46:34] - Setting Model No. with value : CORSAIR 60GB
[Tue 03/01/2016 19:46:34] - Setting Power Management Version with value : 0
[Tue 03/01/2016 19:46:34] - Setting Serial Number with value : 1234567890
[Tue 03/01/2016 19:46:34] - Total of 1 valid MaxLBA settings were setup to be written to the drive.
[Tue 03/01/2016 19:46:36] - Successfully applied the remaining ConfigUniqueDrive settings...
[Tue 03/01/2016 19:46:36] - Issuing an IdleImmediate command to the drive...
[Tue 03/01/2016 19:46:36] - Not an Enterprise drive,so, continuing without setting master password..
[Tue 03/01/2016 19:46:36] - End of Genesis manufacturing log.
[Tue 03/01/2016 19:46:36] - Exiting...
[Tue 03/01/2016 19:46:36] - Overall Result for Device: /dev/sg0 ****** PASS ******
snip45
Цитата:
snip45 посмотри пожалуйста у тебя к конфигу 22189 vic файл так называется
22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
Цитата:
Ну так 22189 из доступного должно подойти. В логе MT29F128G08CFAAAWP,предположу,что файл был переименован случайно (из 22193 например). Микры не совместимы.
snip45 посмотри пожалуйста у тебя к конфигу 22189 vic файл так называется
22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
Progaks Сейчас нет доступа к своему компу,но уверен, не может название микр быть другим чем на плате. Сам восстанавливал 2шт таких 1:1 как у тебя конфигом 22189. Правда скорость не фонтан с этим номером. Можно в HEX редакторе открыть vic,там в заголовке название конфига и номер фирмвари есть. Лучше скачать и распаковать самому всё,меньше проблем.
snip45 есть ссылка на тот конфиг которым ты шил?
ура ура! всем ОГРОМНОЕ ЧЕЛОВЕЧЕСКОЕ СПАСИБО!винт ожил не знаю надолго иль нет но ожил! ставлю систему
Цитата:
к конфигу 22189 vic файл так называется
22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
в базе прошивки 5.8.2:
22189_mf_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
[more] Процесс ещё немного сдвинулся сместа
но опять лезет ошибка
Код: <?xml version = "1.0"?>
<Genesis_Log>
<Log_Body>
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Overall Summary:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Start Time: Tue, 03/01/2016 @ 23:12:23
End Time: Tue, 03/01/2016 @ 23:13:54
OverallResult: FAIL
ExitCode: (0x10090012:SF_GENESIS_IDENTIFY_ERROR)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Environment Settings:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Input Parameters:
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
Log File: SF_Genesis_Main_Log__Tue_03.01.2016_23.12.23.log
Hostname: localhost.localdomain
Host IP Address: 127.0.0.1
Port Number: 1
DeviceName: /dev/sg1
SF_Genesis Version: v1.7.0.01020130612-fc14-32bit
SF_Core Library Version: v1.7.1.20130612-fc14-32bit
SF_OS_Information: Linux 4.2.3-300.fc23.i686 #1 SMP Mon Oct 5 16:26:47 UTC 2015 i686
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Post Processing Device Information:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
WWN OUI: UNKNOWN
WWN UniqueID: UNKNOWN
Serial No.: UNKNOWN
Model No.: UNKNOWN
Firmware Revision: UNKNOWN
ROM Revision: UNKNOWN
NAND Page Size: UNKNOWN
Number Of Chip Enable: UNKNOWN
Logical Sectors: UNKNOWN
NAND ID: UNKNOWN
Flash Manufacturer: UNKNOWN
Flash Device: UNKNOWN
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:23] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:23] - Instructing the operating system to purge any existing cached data for device: '1:0:0:0'
[Tue 03/01/2016 23:12:29] - Issuing a discovery command for device: '1:0:0:0'
[Tue 03/01/2016 23:12:35] - Discovery command completed...
[Tue 03/01/2016 23:12:35] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 23:12:40] - Device designation string '1:0:0:0' is mapped to node '/dev/sg1'
[Tue 03/01/2016 23:12:40] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg1
MFP Package Filename = /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
Configuration File = /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
Serial No. = 12345
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:40] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:12:40] - Validating Manufacturing Firmware Package: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
[Tue 03/01/2016 23:12:43] - Successfully opened the package: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
[Tue 03/01/2016 23:12:43] - file /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig Loaded successfully
[Tue 03/01/2016 23:12:43] - Warning: Unable to query diagnostics information to perform power management settings check
[Tue 03/01/2016 23:12:43] - B01 Power Management configuration request detected
[Tue 03/01/2016 23:12:43] - Successfully extracted *.DriveConfig file: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
[Tue 03/01/2016 23:12:43] - Extracted Config_ID: 1 (22189) in DriveConfig file: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
[Tue 03/01/2016 23:12:43] - Extracted SerialOutputControl: 0
[Tue 03/01/2016 23:12:43] - Searching for flashware image for configuration 22189
[Tue 03/01/2016 23:12:43] - Manifest found for configuration 22189
[Tue 03/01/2016 23:12:43] - Flashware image extracted: 22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
[Tue 03/01/2016 23:12:43] - Searching for manufacturing image for configuration 22189
[Tue 03/01/2016 23:12:43] - Manifest found for configuration 22189
[Tue 03/01/2016 23:12:43] - Manufacturing image extracted: 22189_mf_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
[Tue 03/01/2016 23:12:43] - Proceeding in ROM mode, download feature 3...
[Tue 03/01/2016 23:12:43] - Successfully downloaded MFB to the drive...
[Tue 03/01/2016 23:12:43] - Waiting (5 sec) for the drive to settle...
[Tue 03/01/2016 23:12:48] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:12:48] - Firmware revision reported to be: '503ABBM0'. This indicates MFB download was successful.
[Tue 03/01/2016 23:12:48] - Successfully enabled SMART capabilities...
[Tue 03/01/2016 23:12:50] - Successfully issued a diagnostic unlock...
[Tue 03/01/2016 23:12:51] - Performing the flash test of block 0 (0x0000)...
[Tue 03/01/2016 23:12:53] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 2 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 16
Number of failures: 0
Number of Passed with warnings: 16
No. Passed without warnings: 0
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:53] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 234441648
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34860 (0x882C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 0
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:13:30] - FORMAT command completed...
[Tue 03/01/2016 23:13:30] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 23:13:32] - Setting up the stamp information through CDU command...
[Tue 03/01/2016 23:13:35] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 23:13:37] - Downloading the flashware to the drive... feature 3
[Tue 03/01/2016 23:13:39] - Successfully downloaded flashware to the drive...
[Tue 03/01/2016 23:13:39] - Waiting (15 sec) for the drive to settle...
[Tue 03/01/2016 23:13:54] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:13:54] - FATAL_ERROR: Did not recieve the correct firmware revision. it is reported to be: '20DABBR0', indicating flashware download has failed.
[Tue 03/01/2016 23:13:54] - End of Genesis manufacturing log.
[Tue 03/01/2016 23:13:54] - Exiting...
</Log_Body>
<Overall_Summary>
<Start_Time> Tue, 03/01/2016 @ 23:12:23 </Start_Time>
<End_Time> Tue, 03/01/2016 @ 23:13:54 </End_Time>
<Overall_Result> FAIL </Overall_Result>
<Exit_Code> (0x10090012:SF_GENESIS_IDENTIFY_ERROR) </Exit_Code>
</Overall_Summary>
<Environment_Settings>
<Input_Parameters>
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
</Input_Parameters>
<Log_File> SF_Genesis_Main_Log__Tue_03.01.2016_23.12.23.log </Log_File>
<Hostname> localhost.localdomain </Hostname>
<Host_IP_Address> 127.0.0.1 </Host_IP_Address>
<Port_Number> 1 </Port_Number>
<Device_Name> /dev/sg1 </Device_Name>
<SF_Genesis_Version> v1.7.0.01020130612-fc14-32bit </SF_Genesis_Version>
<SF_Core_Library_Version> v1.7.1.20130612-fc14-32bit </SF_Core_Library_Version>
<SF_OS_Information> Linux 4.2.3-300.fc23.i686 #1 SMP Mon Oct 5 16:26:47 UTC 2015 i686 </SF_OS_Information>
</Environment_Settings>
<Post_Processing_Device_Info>
<WWN_OUI> UNKNOWN </WWN_OUI>
<WWN_UniqueID> UNKNOWN </WWN_UniqueID>
<Serial_Number> UNKNOWN </Serial_Number>
<Model_Number> UNKNOWN </Model_Number>
<Firmware_Revision> UNKNOWN </Firmware_Revision>
<ROM_Revision> UNKNOWN </ROM_Revision>
<NAND_Page_Size> UNKNOWN </NAND_Page_Size>
<Number_Of_Chip_Enable> UNKNOWN </Number_Of_Chip_Enable>
<Logical_Sectors> UNKNOWN </Logical_Sectors>
<NAND_ID> UNKNOWN </NAND_ID>
<Flash_Manufacturer> UNKNOWN </Flash_Manufacturer>
<Flash_Device> UNKNOWN </Flash_Device>
</Post_Processing_Device_Info>
</Genesis_Log>
[Tue 03/01/2016 23:13:54] - Overall Result for Device: /dev/sg1 ****** FAIL ******
но опять лезет ошибка
Код: <?xml version = "1.0"?>
<Genesis_Log>
<Log_Body>
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Overall Summary:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Start Time: Tue, 03/01/2016 @ 23:12:23
End Time: Tue, 03/01/2016 @ 23:13:54
OverallResult: FAIL
ExitCode: (0x10090012:SF_GENESIS_IDENTIFY_ERROR)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Environment Settings:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Input Parameters:
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
Log File: SF_Genesis_Main_Log__Tue_03.01.2016_23.12.23.log
Hostname: localhost.localdomain
Host IP Address: 127.0.0.1
Port Number: 1
DeviceName: /dev/sg1
SF_Genesis Version: v1.7.0.01020130612-fc14-32bit
SF_Core Library Version: v1.7.1.20130612-fc14-32bit
SF_OS_Information: Linux 4.2.3-300.fc23.i686 #1 SMP Mon Oct 5 16:26:47 UTC 2015 i686
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Post Processing Device Information:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
WWN OUI: UNKNOWN
WWN UniqueID: UNKNOWN
Serial No.: UNKNOWN
Model No.: UNKNOWN
Firmware Revision: UNKNOWN
ROM Revision: UNKNOWN
NAND Page Size: UNKNOWN
Number Of Chip Enable: UNKNOWN
Logical Sectors: UNKNOWN
NAND ID: UNKNOWN
Flash Manufacturer: UNKNOWN
Flash Device: UNKNOWN
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:23] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:23] - Instructing the operating system to purge any existing cached data for device: '1:0:0:0'
[Tue 03/01/2016 23:12:29] - Issuing a discovery command for device: '1:0:0:0'
[Tue 03/01/2016 23:12:35] - Discovery command completed...
[Tue 03/01/2016 23:12:35] - Waiting 5 seconds for the system to settle...
[Tue 03/01/2016 23:12:40] - Device designation string '1:0:0:0' is mapped to node '/dev/sg1'
[Tue 03/01/2016 23:12:40] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg1
MFP Package Filename = /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
Configuration File = /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
Serial No. = 12345
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:40] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:12:40] - Validating Manufacturing Firmware Package: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
[Tue 03/01/2016 23:12:43] - Successfully opened the package: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
[Tue 03/01/2016 23:12:43] - file /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig Loaded successfully
[Tue 03/01/2016 23:12:43] - Warning: Unable to query diagnostics information to perform power management settings check
[Tue 03/01/2016 23:12:43] - B01 Power Management configuration request detected
[Tue 03/01/2016 23:12:43] - Successfully extracted *.DriveConfig file: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
[Tue 03/01/2016 23:12:43] - Extracted Config_ID: 1 (22189) in DriveConfig file: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
[Tue 03/01/2016 23:12:43] - Extracted SerialOutputControl: 0
[Tue 03/01/2016 23:12:43] - Searching for flashware image for configuration 22189
[Tue 03/01/2016 23:12:43] - Manifest found for configuration 22189
[Tue 03/01/2016 23:12:43] - Flashware image extracted: 22189_fw_cl_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
[Tue 03/01/2016 23:12:43] - Searching for manufacturing image for configuration 22189
[Tue 03/01/2016 23:12:43] - Manifest found for configuration 22189
[Tue 03/01/2016 23:12:43] - Manufacturing image extracted: 22189_mf_mlc_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S_PP_R00714_s512.vic
[Tue 03/01/2016 23:12:43] - Proceeding in ROM mode, download feature 3...
[Tue 03/01/2016 23:12:43] - Successfully downloaded MFB to the drive...
[Tue 03/01/2016 23:12:43] - Waiting (5 sec) for the drive to settle...
[Tue 03/01/2016 23:12:48] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:12:48] - Firmware revision reported to be: '503ABBM0'. This indicates MFB download was successful.
[Tue 03/01/2016 23:12:48] - Successfully enabled SMART capabilities...
[Tue 03/01/2016 23:12:50] - Successfully issued a diagnostic unlock...
[Tue 03/01/2016 23:12:51] - Performing the flash test of block 0 (0x0000)...
[Tue 03/01/2016 23:12:53] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0022 | N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 2 | 0x0042 | N3,N6 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 16
Number of failures: 0
Number of Passed with warnings: 16
No. Passed without warnings: 0
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:12:53] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 234441648
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34860 (0x882C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 0
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 03/01/2016 23:13:30] - FORMAT command completed...
[Tue 03/01/2016 23:13:30] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 23:13:32] - Setting up the stamp information through CDU command...
[Tue 03/01/2016 23:13:35] - Waiting (2 sec) for the drive to settle...
[Tue 03/01/2016 23:13:37] - Downloading the flashware to the drive... feature 3
[Tue 03/01/2016 23:13:39] - Successfully downloaded flashware to the drive...
[Tue 03/01/2016 23:13:39] - Waiting (15 sec) for the drive to settle...
[Tue 03/01/2016 23:13:54] - Successfully received the IDENTIFY data from the drive...
[Tue 03/01/2016 23:13:54] - FATAL_ERROR: Did not recieve the correct firmware revision. it is reported to be: '20DABBR0', indicating flashware download has failed.
[Tue 03/01/2016 23:13:54] - End of Genesis manufacturing log.
[Tue 03/01/2016 23:13:54] - Exiting...
</Log_Body>
<Overall_Summary>
<Start_Time> Tue, 03/01/2016 @ 23:12:23 </Start_Time>
<End_Time> Tue, 03/01/2016 @ 23:13:54 </End_Time>
<Overall_Result> FAIL </Overall_Result>
<Exit_Code> (0x10090012:SF_GENESIS_IDENTIFY_ERROR) </Exit_Code>
</Overall_Summary>
<Environment_Settings>
<Input_Parameters>
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/FW_SF-2000_5_0_3_Client_MP.1.mfp
argv[4]: /home/admin/ssd/FW/FW_SF-2000_5_0_3_Client_MP--1/Configuration_Files/22189.1.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/admin/Ssd_log.log
</Input_Parameters>
<Log_File> SF_Genesis_Main_Log__Tue_03.01.2016_23.12.23.log </Log_File>
<Hostname> localhost.localdomain </Hostname>
<Host_IP_Address> 127.0.0.1 </Host_IP_Address>
<Port_Number> 1 </Port_Number>
<Device_Name> /dev/sg1 </Device_Name>
<SF_Genesis_Version> v1.7.0.01020130612-fc14-32bit </SF_Genesis_Version>
<SF_Core_Library_Version> v1.7.1.20130612-fc14-32bit </SF_Core_Library_Version>
<SF_OS_Information> Linux 4.2.3-300.fc23.i686 #1 SMP Mon Oct 5 16:26:47 UTC 2015 i686 </SF_OS_Information>
</Environment_Settings>
<Post_Processing_Device_Info>
<WWN_OUI> UNKNOWN </WWN_OUI>
<WWN_UniqueID> UNKNOWN </WWN_UniqueID>
<Serial_Number> UNKNOWN </Serial_Number>
<Model_Number> UNKNOWN </Model_Number>
<Firmware_Revision> UNKNOWN </Firmware_Revision>
<ROM_Revision> UNKNOWN </ROM_Revision>
<NAND_Page_Size> UNKNOWN </NAND_Page_Size>
<Number_Of_Chip_Enable> UNKNOWN </Number_Of_Chip_Enable>
<Logical_Sectors> UNKNOWN </Logical_Sectors>
<NAND_ID> UNKNOWN </NAND_ID>
<Flash_Manufacturer> UNKNOWN </Flash_Manufacturer>
<Flash_Device> UNKNOWN </Flash_Device>
</Post_Processing_Device_Info>
</Genesis_Log>
[Tue 03/01/2016 23:13:54] - Overall Result for Device: /dev/sg1 ****** FAIL ******
Цитата:
Подробнее...
основная прошивка не взлетела
цепляй uart/сom порт и смотри на что ругается
[more] выкладываю два лога
1 терминал
Код: [ROM] Undec Cmd 0xe0
[ROM] Hard Reset ===> Link is Down.
[ROM] PHY Ready
[ROM] Sig Sent
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000009
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000008, count:00000008, tag:0000000a
[ROM] Undec Cmd 0xec
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000018
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000019
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000008, count:00000008, tag:0000001a
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000010, count:00000008, tag:0000001b
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000020, count:00000008, tag:0000001c
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xb0
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> *** MFB 503 Jul 19 2012 20:30:22 B:FW_PPRO_MP3_5_0_2_20120315:FW_PPRO_5_0_
3_Release-448193 ***
<MFB> *** Config cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S ***
*** Chip RevId from HW: B01 (ID=288571), FW Targeted For: B02 ASIC ***
<MFB> *** SysClk : 300 MHz
*** Packer : 500 MHz
*** Flash : 800 MHz
*** FlaDiv : 6
<MFB> *** TMI_TS : 2
<MFB> GPIO0:1
<MFB> Scap charge wait
<MFB> Scap charge done
<usrspc>libSfStartC enter cfg:3fff3058
<MFB> Flash Rblock Test on 0 - bus:2 ce:2 die:1 lane:4 pageCnt:1 correctPwr:128
seed:dead3664 markers:2000
Errors in BUS:0 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0022, LAN
E 3: 0002, <MFB> ]
Errors in BUS:1 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0002, <MFB> ]
Errors in BUS:0 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
Errors in BUS:1 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0042, LAN
E 3: 0002, <MFB> ]
<MFB> Read Device ID: 2C 88 04 4B A9 00
<MFB> == Format mode ONE align 0 ==
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> Flash ID Check
<MFB> Creating New Root
<MFB> Bad Block Discovery ...
<MFB> Number of Bad Blocks for SE/plane/lane
<MFB> SE pl: ln0 ln1 ln2 ln3
<MFB> 0 0: 1 1 1 1
<MFB> 0 1: 1 1 1 1
<MFB> 1 0: 1 1 1 1
<MFB> 1 1: 1 1 2 1
<MFB> 2 0: 1 1 1 1
<MFB> 2 1: 1 1 1 1
<MFB> 3 0: 1 1 1 1
<MFB> 3 1: 1 1 1 1
<MFB> Total Bad Block number is: 33 out of 65536
<MFB> Added donor[0]= 45
<MFB> Added donor[1]= 1335
<MFB> Enabling Remap Unit...
<MFB> Erasing All Virgin Blocks...
<MFB> Creating the Root Record ...
<MFB> Input PE: 0
<MFB> Drive RDD:100000 RDD Low:100000, PE: 3000 Options:0000 Warranty: 0
<MFB> WP Circuit Not Present
<MFB> Initialize the Root ...
<MFB> Found a valid Config Record.
<MFB> Bus Width [bits] = 32
<MFB> Number of CE = 2
<MFB> Number of Die / CE = 1
<MFB> CE CFG (Bus Mode) = 2-DIMM
<MFB> Number of Bus = 2
<MFB> Flash Page Size = 8192
<MFB> Flash Page / Block = 256
<MFB> Number of Block / Die = 2048
<MFB> E-Page Size = 512
<MFB> ECC Bytes = 27
<MFB> ECC Correction Power = 16
<MFB> EVT LOG. Panic Dump slot 0 epa 0x00020002
<MFB> EVT LOG. Panic Dump slot 1 epa 0x20020002
<MFB> EVT LOG. Panic Dump slot 2 epa 0x00020082
<MFB> EVT LOG. Panic Dump slot 3 epa 0x20020082
<MFB> Saving Bad Block List ...
<MFB> Initializing SMART root file ...
<MFB> InitSmartLogRootFile is done
<MFB> Saving Grown Defect List ...
<MFB> Initializing Life Table ...
<MFB> Saving Life Table ...
<MFB> Set LBA Offset to 0 ...
<MFB> Clearing the Map Table ...
<MFB> Clearing the SIN Table ...
<MFB> Saving the MAP Table1 ...
<MFB> Saving the MAP Table2 ...
<MFB> Saving the SIN Table ...
<MFB> Saving the Remap Table ...
---> SAVE REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes 2 ticks <---
<MFB> Verifying the Remap Table ...
---> LOAD REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes, 1 ticks, 0 remapped <---
<MFB> Saving the RD Table ...
<MFB> Saving the ID Data ...
<MFB> Saving the Free Table ...
<MFB> Finalizing the ROOT ...
<MFB> Factory Setup finished; you may reboot or download Flashware now.
<usrspc>SCT_CONFIG_DRIVE_UNIQUE: user space synced
<MFB> Firmware Fuse=0xFC00FC00, computed value=0xFC00
<MFB> PPRO_STAMP FROM IMAGE: 06 14 00 fc 00 00 20 20
<MFB> STAMP OK at offset 0x000000
<MFB> Need 380672 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 315136 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 249600 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 184064 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 118528 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 52992 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Validate SHA on Input Stream Microcode: PASS!
<MFB> Did not find appendix signature.
<MFB> Info 1: not a valid appendix.
<MFB> Validate SHA on Root File 3: PASS!
<MFB> Validate SHA on Root File 4: PASS!
<MFB> Download Microcode PASS!
<MFB> SATA_UPDATE_COMPLETE
<MFB> Warm Start (state=14) - Resetting ALL hardware blocks!
[ROM] Chip ID 0x200026BB
*** ROM Rev 20D Dec 20 2010 Build 288571 ***
[ROM] Force Download: waiting for Download Microcode Command...
[ROM] Waiting for Link to come up...
[ROM] Link is UP.
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
1 терминал
Код: [ROM] Undec Cmd 0xe0
[ROM] Hard Reset ===> Link is Down.
[ROM] PHY Ready
[ROM] Sig Sent
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000009
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000008, count:00000008, tag:0000000a
[ROM] Undec Cmd 0xec
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000018
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000019
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000008, count:00000008, tag:0000001a
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000010, count:00000008, tag:0000001b
[ROM] Data Cmd
[ROM] READ NCQ CMD
[ROM] R_NCQ done, lba:00000020, count:00000008, tag:0000001c
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xb0
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
[ROM] Undec Cmd 0x92
[ROM] non-DMA
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> *** MFB 503 Jul 19 2012 20:30:22 B:FW_PPRO_MP3_5_0_2_20120315:FW_PPRO_5_0_
3_Release-448193 ***
<MFB> *** Config cfg/cfg_MLC_Micron_64Gb_MT29F128G08CFAAAWP_2Q_2C_1D_S ***
*** Chip RevId from HW: B01 (ID=288571), FW Targeted For: B02 ASIC ***
<MFB> *** SysClk : 300 MHz
*** Packer : 500 MHz
*** Flash : 800 MHz
*** FlaDiv : 6
<MFB> *** TMI_TS : 2
<MFB> GPIO0:1
<MFB> Scap charge wait
<MFB> Scap charge done
<usrspc>libSfStartC enter cfg:3fff3058
<MFB> Flash Rblock Test on 0 - bus:2 ce:2 die:1 lane:4 pageCnt:1 correctPwr:128
seed:dead3664 markers:2000
Errors in BUS:0 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0022, LAN
E 3: 0002, <MFB> ]
Errors in BUS:1 CE: 0 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0002, <MFB> ]
Errors in BUS:0 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0002, LAN
E 3: 0003, <MFB> ]
Errors in BUS:1 CE: 1 DIE:0 [ LANE 0: 0002, LANE 1: 0002, LANE 2: 0042, LAN
E 3: 0002, <MFB> ]
<MFB> Read Device ID: 2C 88 04 4B A9 00
<MFB> == Format mode ONE align 0 ==
<MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
<MFB> Flash ID Check
<MFB> Creating New Root
<MFB> Bad Block Discovery ...
<MFB> Number of Bad Blocks for SE/plane/lane
<MFB> SE pl: ln0 ln1 ln2 ln3
<MFB> 0 0: 1 1 1 1
<MFB> 0 1: 1 1 1 1
<MFB> 1 0: 1 1 1 1
<MFB> 1 1: 1 1 2 1
<MFB> 2 0: 1 1 1 1
<MFB> 2 1: 1 1 1 1
<MFB> 3 0: 1 1 1 1
<MFB> 3 1: 1 1 1 1
<MFB> Total Bad Block number is: 33 out of 65536
<MFB> Added donor[0]= 45
<MFB> Added donor[1]= 1335
<MFB> Enabling Remap Unit...
<MFB> Erasing All Virgin Blocks...
<MFB> Creating the Root Record ...
<MFB> Input PE: 0
<MFB> Drive RDD:100000 RDD Low:100000, PE: 3000 Options:0000 Warranty: 0
<MFB> WP Circuit Not Present
<MFB> Initialize the Root ...
<MFB> Found a valid Config Record.
<MFB> Bus Width [bits] = 32
<MFB> Number of CE = 2
<MFB> Number of Die / CE = 1
<MFB> CE CFG (Bus Mode) = 2-DIMM
<MFB> Number of Bus = 2
<MFB> Flash Page Size = 8192
<MFB> Flash Page / Block = 256
<MFB> Number of Block / Die = 2048
<MFB> E-Page Size = 512
<MFB> ECC Bytes = 27
<MFB> ECC Correction Power = 16
<MFB> EVT LOG. Panic Dump slot 0 epa 0x00020002
<MFB> EVT LOG. Panic Dump slot 1 epa 0x20020002
<MFB> EVT LOG. Panic Dump slot 2 epa 0x00020082
<MFB> EVT LOG. Panic Dump slot 3 epa 0x20020082
<MFB> Saving Bad Block List ...
<MFB> Initializing SMART root file ...
<MFB> InitSmartLogRootFile is done
<MFB> Saving Grown Defect List ...
<MFB> Initializing Life Table ...
<MFB> Saving Life Table ...
<MFB> Set LBA Offset to 0 ...
<MFB> Clearing the Map Table ...
<MFB> Clearing the SIN Table ...
<MFB> Saving the MAP Table1 ...
<MFB> Saving the MAP Table2 ...
<MFB> Saving the SIN Table ...
<MFB> Saving the Remap Table ...
---> SAVE REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes 2 ticks <---
<MFB> Verifying the Remap Table ...
---> LOAD REMAP/DONOR FID 19 [tbl 1 off 00000 sz 30000] [tbl 2 off 30000 sz 00cc
8] <MFB> TOTAL 30CC8 (199880) bytes, 1 ticks, 0 remapped <---
<MFB> Saving the RD Table ...
<MFB> Saving the ID Data ...
<MFB> Saving the Free Table ...
<MFB> Finalizing the ROOT ...
<MFB> Factory Setup finished; you may reboot or download Flashware now.
<usrspc>SCT_CONFIG_DRIVE_UNIQUE: user space synced
<MFB> Firmware Fuse=0xFC00FC00, computed value=0xFC00
<MFB> PPRO_STAMP FROM IMAGE: 06 14 00 fc 00 00 20 20
<MFB> STAMP OK at offset 0x000000
<MFB> Need 380672 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 315136 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 249600 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 184064 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 118528 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Need 52992 More!
<MFB> SATA_UPDATE_IN_PROGRESS
<MFB> Validate SHA on Input Stream Microcode: PASS!
<MFB> Did not find appendix signature.
<MFB> Info 1: not a valid appendix.
<MFB> Validate SHA on Root File 3: PASS!
<MFB> Validate SHA on Root File 4: PASS!
<MFB> Download Microcode PASS!
<MFB> SATA_UPDATE_COMPLETE
<MFB> Warm Start (state=14) - Resetting ALL hardware blocks!
[ROM] Chip ID 0x200026BB
*** ROM Rev 20D Dec 20 2010 Build 288571 ***
[ROM] Force Download: waiting for Download Microcode Command...
[ROM] Waiting for Link to come up...
[ROM] Link is UP.
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
[ROM] Undec Cmd 0xef
[ROM] Undec Cmd 0xec
Force Download: waiting for Download Microcode Command...
Progaks, ты перемычку то не забыл убрать перед запуском genesis ?
Progaks, ты перемычку то не забыл убрать перед запуском genesis ?
Цитата:
ты перемычку то не забыл убрать перед запуском genesis ?
AlexeyIII, вот СПАСИБО тебе большое
Цитата:
ты перемычку то не забыл убрать перед запуском genesis
как ее вообще можно оставить, если ее только один раз перед подключением замыкать надо? 
Цитата:
как ее вообще можно оставить, если ее только один раз перед подключением замыкать надо?
ну что можно сказать (тупанул) )))
Добавлено:
Всем СПС кто откликнулся помочь
Добрый день! Подскажите какую прошивку использовать для SSD INTEL 335 80GB контроллер SF- 2281 память 6[29f16b08ccmf2?
всем привет! в общем установил на прошитый корсар 60 винду 8.1 х-64 , обновился . скачал и запустил тест hd-tune 2.55 вот что пишет
transfer rate
minimum 99.8 mb/sec
maximum 202.0 mb/sec
average 182.4mb/sec
access time 0.2 ms
burst rate 155.7mb/sec
cpu usage 16.2%
Добавлено:
этот девайс установлен в ноутбук самсунг Р-717 интел пентиум дуал кор Т4500 2.3 ГГц памяти 4 ГБ РС-6400 ддр-2
Добавлено:
до этого стоял в системнике z-68apd3 intel i5 2500k 3.3GHz 16gb ddr-3 1600 GHz
там он с новья только под вин-7 х-64 показывал
transfer rate
minimum 115.3 mb/sec
maximum 391.6 mb/sec
average 298.4mb/sec
access time 0.1 ms
burst rate 268.6mb/sec
cpu usage -1.0%
вот особенно минус 1 процент заинтересовал))
скрины все делал сам когда купил и сейчас после прошивки. вот вопрос что так износились ячейки ? или все же прошил неудачно? или просто разные машины (лаптоп и стационарка)
очень интересно мнение людей послушать
transfer rate
minimum 99.8 mb/sec
maximum 202.0 mb/sec
average 182.4mb/sec
access time 0.2 ms
burst rate 155.7mb/sec
cpu usage 16.2%
Добавлено:
этот девайс установлен в ноутбук самсунг Р-717 интел пентиум дуал кор Т4500 2.3 ГГц памяти 4 ГБ РС-6400 ддр-2
Добавлено:
до этого стоял в системнике z-68apd3 intel i5 2500k 3.3GHz 16gb ddr-3 1600 GHz
там он с новья только под вин-7 х-64 показывал
transfer rate
minimum 115.3 mb/sec
maximum 391.6 mb/sec
average 298.4mb/sec
access time 0.1 ms
burst rate 268.6mb/sec
cpu usage -1.0%
вот особенно минус 1 процент заинтересовал))
скрины все делал сам когда купил и сейчас после прошивки. вот вопрос что так износились ячейки ? или все же прошил неудачно? или просто разные машины (лаптоп и стационарка)
очень интересно мнение людей послушать
Цитата:
для SSD INTEL 335 80G
22455 или 27348
Цитата:
или просто разные машины
Как их вообще можно сравнивать
Даже просто из-за различия SATA 2 и SATA 3.так что в ноуте сата 2? как вообще увидеть или проверить какой сата ? может какая программа есть для теста?
Цитата:
так что в ноуте сата 2? как вообще увидеть или проверить какой сата ? может какая программа есть для теста?
HWiNFO
Страницы: 1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253
Предыдущая тема: Накрылся Hdd с ошибкой A disk read error
Форум Ru-Board.club — поднят 15-09-2016 числа. Цель - сохранить наследие старого Ru-Board, истории становления российского интернета. Сделано для людей.