Цитата:
У меня на Win7 x64 в SW2010 не подключается SW ToolBox Browser.
Такая же ерунда и в SW2009 SP4.0 на Win Vista x64 SP2. В конфигурацию войти получается. Сохранить ее тоже. Но по щелчку меню Toolbox предлагается только "Конфигурация..."
У меня на Win7 x64 в SW2010 не подключается SW ToolBox Browser.
пользовать макросы
по подробней или хотя бы ссылочку, где посмотреть...
Dear SolidWorks Professional,
SolidWorks 2009 SP5 (x64), SolidWorks 2010 SP1 (x64), and SolidWorks 2010 SP2 (x64) have been temporality removed from the SolidWorks Downloads pages due to the technical issue listed below.
An issue with PhotoWorks has been identified in 64-bit versions of SolidWorks 2009 SP5, SolidWorks 2010 SP1, and SolidWorks 2010 SP2 in which the SolidWorks installation, the operating system, program files and data files may become damaged or unrecoverable if the PhotoWorks add-in is enabled when SolidWorks is running and the SolidWorks process is already using more than 2GB of virtual memory. These service packs have been removed from the web site as a precaution in order to prevent the risk of damage to customers systems under these circumstances.
This problem does not affect 32-bit versions of SolidWorks; hence all 32-bit Service Packs are still available for download. Furthermore, SolidWorks 2010 SP0 (x64) is not affected, nor are SolidWorks 2009 SP4.1 (x64) and earlier Service Packs of 2009. Please note also that this issue only pertains to enabling the PhotoWorks add-in and has no effect on the use of PhotoView 360 for renderings.
The issue is documented in Knowledge Base solution S-046282, included below for reference, which will be updated as more information is available. Immediate hot fixes are planned for each of these service pack versions, and will be released as soon as possible. SolidWorks 2009 SP5.1 and SolidWorks 2010 SP2.1 point release service packs are also being developed with a fix for this issue.
Jan 19, 2010 Critical Hotfix for PhotoWorks on 64-bit operating systems with SolidWorks 2009 SP5, 2010 SP1 or 2010 SP2
All customers with PhotoWorks on a 64-bit operating system with SolidWorks 2009 SP5, 2010 SP1, or 2010 SP2 MUST apply this hotfix in response to SPR# 535417.
A PhotoWorks issue has been identified in 64-bit operating system versions with SolidWorks 2009 SP5, SolidWorks 2010 SP1, and SolidWorks 2010 SP2. The SolidWorks installation, operating system, program files, and data files may become damaged or unrecoverable if the PhotoWorks add-in is enabled when SolidWorks is running and the SolidWorks process is already using more than 2GB of virtual memory. See SolidWorks Technical Alerts for further details.
Hotfix instructions:
1) Select the version to hotfix (Note: SolidWorks cannot be running when the hotfix is applied):
- SolidWorks 2009 SP5.0
- SolidWorks 2010 SP1.0
- SolidWorks 2010 SP2.0
2) Select whether Run or Save the hotfix. Use Save if you are applying the hotfix to more than one computer.
3) Select Run to extract the hotfix.
4) Select Run to accept the warning.
5) Unzip the files and the hotfix will be applied.
6) Patch complete. Note: You will need to uninstall this patch before applying
SolidWorks 2009 SP5.1, SolidWorks 2010 SP2.1 or higher.
Vortex crosses the pressure opening
режим перестроения сетки во время счета
Это Refinement имеется в виду
Запустился расчет на 1,1млн ячеек.
Расчет на 8-м уровне сетки все равно выдал VORTEXа
на чертеже указать Конусность
1. Сначала добавить значек конусности. Для этого надо в файл
"C:\Program Files\SolidWorks Corp\SolidWorks\lang\russian\GTOL.sym" (или где он там у Вас..) в любом текстовом редакторе добавить в раздел "Обозначения для модификации" следующие строки (при выгруженном солиде):
Страницы: 12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879808182838485868788
Предыдущая тема: KAV / AVP / Антивирус Касперского (Часть 8)